A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and speed 650 r.p.m. is supported in bearings on either side. Calculate the total load due to the power transmitted, the pressure angle being 25°. then calculate the total load when the speed be 1300 r.p.m to transmit 250 kW of power.

A single reduction gear of 120 kW with a pinion 250 mm pitch circle diameter and speed 650 r.p.m. is supported in bearings on either side. Calculate the total load due to the power transmitted, the pressure angle being 25°. then calculate the total load when the speed be 1300 r.p.m to transmit 250 kW of power.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 60P: A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a...

See similar textbooks

Similar questions

The arm of a starter is held in the "ON" position by means of an eleetromagnet. The torque exerted by the spring is 5 Nm and the effective radius at which the force is exerted is 10 cm. Area of each pole face is 2.5 cm? and each air gap is 0.4 mm. Find the minimum number of ampere-turns (AT) required to keep the arm in the "ON" position.?
Find the Young’s modulus of the wire. (g= 9.81 m/s/s)
The 100-kg uniform rectangular plate is supported by an ideal pivot at O and a spring which must be compressed prior to being slipped into place at point A. If the modulus of the spring is k = 2,000 N/m, what must be its undeformed length L in mm?
The 12m boom AB weighs 10 kN, the distance of the center of gravity being 6m from hinge A. For the position shown, determine the tension T in the cable BC and the reaction at hinge A.
The lever in Fig. has a weight W at one end and is tiedto a cylinder at the left end. The cylinder has negligibleweight and buoyancy and slides upward through a fi lm ofheavy oil of viscosity μ . ( a ) If there is no acceleration (uniformlever rotation), derive a formula for the rate of fall V 2of the weight. Neglect the lever weight. Assume a linearvelocity profile in the oil fi lm. ( b ) Estimate the fall velocityof the weight if W = 20 N, L 1 = 75 cm, L 2 = 50 cm, D = 10 cm, L = 22 cm, ∆R = 1 mm, and the oil is glycerin at20 ° C.
To stretch a relaxed biceps muscle 2.5 cm requires a force of 25N. Find the Young’s modulus for the muscle tissue, assuming it to bea uniform cylinder of length 0.24 m and cross-sectional area 47 cm2
In the clevis shown, find the minimum bolt diameter that will support a load P = 14 kips without exceeding a shearing stress of 14 ksi and a bearing stress of 24 ksi.
Suppose that k = 190 N/m 1.Determine the unstretched length of DB to hold the 40-kg crate in the position shown.
A weight of (50kg) affects the lower end of a steel rod of length (80cm) and diameter (0.60cm). What is the magnitude of the elongation of the penis, if you know that the Junk modulus of the bar is equal to (190GPa)?
A solid cylindrical rod BC of length L = 600 mm and radius r = 12 mm is attached to the rigid lever AB of length a = 300 mm and to the fixed support at C. Design requires that the displacement of A not exceed 10 mm when P = 700 N force is applied at A. For a material with G = 70 GPa and τall = 80 MPa what is the safety of the system under displacement and stress considerations.
Can Young’s modulus have a negative value? What about the bulk modulus?
The temperature of the atmosphere oscillates from a maximum near noontime and a minimum near sunrise. Would you consider the atmosphere to be in stable or unstable equilibrium?