A single reduction gearbox made of helical gears has a normal diametral pitch of 12 teeth /in, 28º diametral pitch, a normal pressure angle of 20º, and tooth numbers of 48 and 24 for the gear and pinion respectively. Determine The pitch diameters of gear and pinion respectively Clearance between the mating gear and pinion а. b. с. Centre distance

A single reduction gearbox made of helical gears has a normal diametral pitch of 12 teeth /in, 28º diametral pitch, a normal pressure angle of 20º, and tooth numbers of 48 and 24 for the gear and pinion respectively. Determine The pitch diameters of gear and pinion respectively Clearance between the mating gear and pinion а. b. с. Centre distance

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is drivenat 3000 rev/min while the annulus A2 is driven at 1000 rev/min in theopposite direction. The numbers of teeth in the gears are S1, 16; S2,24; A1, 60; A2, 90. Determine the speed and direction of rotation ofshaft Q. (Q.2) A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A pair of gear/pinion of 42 tooth and 18 tooth with a diametral pitch of 0.7874 teeth/cm and the addendum is 0.8/p and dedendum 1/p. The gear pressure angle is 200 . Compute the center distance of the pair of gears in meters.
lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle. Determine the velocity ratio and the pitch angles. of both gears.
A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.
A pinion having 30 teeth, a module of 2 mm, and rotating at 2000 rpm is to drive a gear rotating at 500 rpm.a) Determine the diametral pitch,b) Number of teeth in the gear, and the center distance.
A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module pitch of 3mm and is meshed with gear B. Whereas gear C that is meshed with gear D has a module pitch of 2.5mm. Gear B and C form a compound gear system. The distance between axis of rotation of driving gear A and driven gear B is equal to 200mm. If gear A has 24 teeth, determine the suitable number of teeth for all gears.
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
a left handed pinion and left handed gear has a helix angle of 40 degree. The two helical gears has a normal diametral pitch of 8 and have a 20 and 34 teeth respectively. The pinion has a rotational speed of 100 rpm. Determine the following: a. angular velocity of the gear b. transverse diametral pitch of each gear c. pitch diameters
Plate gear C of this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B.Determine suitable number of teeth for all the wheels and the exact diameter of pitch circle of the ring.1.1.Calculate the number of teeth of the ring gear D.(3)1.2.State an equation tha relate the number of teeth of gear D, B and C.(1)1.3.Use the table method to calculate the number of teeth of gear B.(13)1.4.Calculate the number of teeth for gear C.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D