A small electric vehicle is powered by a 96 .1V battery and uses a series wound motor. Ithas a step-down chopper for forward driveand a step-up chopper for regenerativebraking. The total armature resistance is 0.1Q, and the armature voltage constant is 10mV/A-rad/s. Descending a hill inregeneration mode the motor speed is 750rev/min and the armature current is aconstant average value of 80 A. Calculatethe value of the duty cycle required and the.available braking power

Given Supply voltage V =96.1 V Armature resistance Ra =0.1 ohm Motor speed N =750 rpm Armature…

A small electric vehicle is powered by a 96 .1 V battery and uses a series wound motor. It has a step-down chopper for forward drive and a step-up chopper for regenerative braking. The total armature resistance is 0.1 Q, and the armature voltage constant is 10 mVIA-rad/s. Descending a hill in regeneration mode the motor speed is 750 rev/min and the armature current is a constant average value of 80 A. Calculate the value of the duty cycle required and the .available braking power

A small electric vehicle is powered by a 96 .1 V battery and uses a series wound motor. It has a step-down chopper for forward drive and a step-up chopper for regenerative braking. The total armature resistance is 0.1 Q, and the armature voltage constant is 10 mVIA-rad/s. Descending a hill in regeneration mode the motor speed is 750 rev/min and the armature current is a constant average value of 80 A. Calculate the value of the duty cycle required and the .available braking power

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.1: Water Pump And Branch Circuit

Problem 21R: Fill in the data for a 16-ampere electric motor, single-phase, no Code letters. a. Branch-circuit...

See similar textbooks

Similar questions

Fill in the data for a 16-ampere electric motor, single-phase, no Code letters. a. Branch-circuit protection, non-time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A b. Branch-circuit protection dual-element, time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A c. Branch-circuit protection instant-trip breaker: Normal setting _____________A Maximum setting _____________A d. Branch-circuit protectioninverse time breaker: Normal rating _____________A Maximum rating _____________A e. Branch-circuit conductor size, Type THHN Ampacity _____________A f. Motor overload protection using dual-element time-delay fuses: Maximum size _____________A
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm
A d.c. shunt machine has armature and field resistances of 0.025 Ω and 80 Ω respectively. When connected to constant 400-V bus-bars and driven as a generator at 450 r.p.m., it delivers 120 kW. Calculate its speed when running as a motor and absorbing 120 kW from the same bus-bars
The armature and field resistances of a series machine are 0.2 ohm and 0.3 ohms respectively. While running as a generator, the generated emf is 250V at 1200rpm. If the machine is run as motor, it takes 4A at220V. At a certain load, the motor takes 30A at 220V. However, on load, the armature reaction weakens the field by 4%. Find the motor speed at this load.
1-The power output of the three phase machine is greater than the single phase machine. (TRUE/FALSE) 2-In thermocouple, when both the junctions are at the same temperature, the potential difference developed across both junction is zero. (TRUE/FALSE) 3-Due to decreased armature m.m.f., the armature reaction during load condition will increase and hence field flux will be distorted. (TRUE/FALSE) 4-While applying voltage in CRO, the grid is positive with respect to cathode. (TRUE/FALSE) 5-Losses in transformers are generally low and thus efficiency is high. (TRUE/FALSE)
1.determine the EMF @ torque equation of the the 4 diff.machines dc,ac,stepper,servo.to solve problems based on its application. Select suitable machine (select 1)and working principle for a given situation (give the situation) and application.
Two dc shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohms run in parallel and supply a total current of 1000 A to the load circuit. If their emf's are 270 V and 265 V, solve the bus bar voltage. Subject:Electrical Machine 1
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
A 32kW, 250V DC shunt machine has an armature and field resistances of 0.05Ω and 120Ω respectively. Determine the total armature power developed when working as generator delivering 32kW output.
A PM DC motor with torque constant kPM is usedto power a hydraulic pump; the pump is a positivedisplacement type and generates a flow proportional tothe pump velocity: qp = kpω. The fluid travels througha conduit of negligible resistance; an accumulator isincluded to smooth out the pulsations of the pump.A hydraulic load (modeled by a fluid resistance R) isconnected between the pipe and a reservoir (assumedat zero pressure). Sketch the motor-pump circuit.Derive the dynamic equations for the system, anddetermine the transfer function between motor voltageand the pressure across the load.
A Shunt Generator delivers 450A at 230V and the resistance of the shunt field and armature are 50Ώ and 0.03 Ώ respectively. Calculate the Generated e.m.f
the armature series field and shunt field resistance of a 125 kw, 250V long shunt cumulative compound DC generator are 0.025ohms, 0.01ohms and 30 ohms, respectively. If the stray power stray loss at rated load is 25 kW, determine the power in the shunt field. Assume a astray load loss of 1% of the load power output (note: Input power generator is equal to the motor brake horsepower, Pin=Pl+Plosses) Choices A. 2034.5 W B.2082.5 W C. 2065.5 W D. 2053.5 W