he given block diagram below represents the velocity control of a DC motor using armature voltage control. TL(s) R(s) + W(s) Go Km 1 Ls+R Js+B Kp H. /here Ge is the controller transfer function, H is the feedback path gain, R(s) is the reference input, Tz(s) is the load torque an ssume, for the ease of computation, L = 2, R=1, J=1, B= 3. 11) Take Km = 0.5, Kb = 2, H = 10, Ge = For what range of K, will the closed loop system be stable? %3D %3D 0 < Kp < 0 0 < Kp < 5.6 0 < K, < 4.8 0 < K, < 2.8

he given block diagram below represents the velocity control of a DC motor using armature voltage control. TL(s) R(s) + W(s) Go Km 1 Ls+R Js+B Kp H. /here Ge is the controller transfer function, H is the feedback path gain, R(s) is the reference input, Tz(s) is the load torque an ssume, for the ease of computation, L = 2, R=1, J=1, B= 3. 11) Take Km = 0.5, Kb = 2, H = 10, Ge = For what range of K, will the closed loop system be stable? %3D %3D 0 < Kp < 0 0 < Kp < 5.6 0 < K, < 4.8 0 < K, < 2.8

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.1P

See similar textbooks

Similar questions

Identification of the physical system components and system integration: draw ablock diagram representing the QUBE-Servo 2 system indicating all the variables, signals,and the control system components. Please could you show what the in detail block diaagrams are given that the input and output of the servocontrol system are:• input: voltage of the motor in V;• output: inertia disk angular position in rad.
The background readgin ( if you needed) is on the screenshot Determine the closed loop transfer function from the speed reference, r, to the angular motor speed output, ω, i.e., Y(s)/R(s). Determine kp and ki in terms of the closed-loop natural frequency, ωn, damping ratio, ζ, motor time constant, τ, and motor gain constant, K. Based on your results from (1) and (2), how would large values of the controller gains, kp and ki, affect the closed-loop undamped natural frequency of the system? Explain how bsp can be used to adjust the speed and overshoot of the response to reference values. (Hint: When answering this question, explain how the value of bsp affects the locations of the closed-loop zeros and/or poles.)
From the next model (DC motor controlled by armature current), obtain: a) The transfer function G(s) = θ(s)/Vc b) The block diagram c) state-space representation d) The poles and zeros diagram
A Data Acquisiton system is used for sensing angular speed with an analog DC Tachometer with asensitivity of 0.05 volt/rpm. The ADC of the system is a 8 bit component and has a full scale of 10V. If the output ofDAC is 101, what is the possible angular speed range?
In control, what is the effect of changing the type of the system and the input signal on the steady-state error?
I am given the task as a trainee control engineer to design a closed-loop controller for the air conditioning unit pictured so that it has the following properties: Maximum overshoot: 10% Maximum time to reach 99% of steady state: 10 seconds Maximum steady-state error: 10% Please find the values of the gain, natural frequency and damping coefficient of the open-loop system to two places after the decimal point. Many thanks :)
design a feedback control system which results in a closed system for the given DC motor that will be given below Damping ratio is 0.6 natural frequency is 10 rad/sec
For a unity feed back system, the open loop function is given by, G(s) = 90(S+9) / S2(S+2)(S+6) Determine the following: (i) The value of positional error constant is : (ii) The value of velocity error constant is : The value of acceleration error constant is : Which input signal can give correct error signal value?
Q6) Develop the block diagram of a closed-loop system for the position control of the DC motor using a PID controller.
Let the no-load speed of the motor driven by a voltage supply Vin be Ωmax, and assume that Ωmax = K Vin. If TPWM is divided into 10 intervals, what is the smallest possible step change in speed for forward full-bridge operation? Let Ωmax = 977 rpm. Enter your answer to the 1st nearest decimal place in rpm.
Given this question for PMDC motor 1) Write the equations of motion for the DC motor in time domain & S-domain. 2) For Full-load and Half-load states, obtain the transfer functions for a.) Torque - Speed b.) Torque - Motor current and this is provided motor specifications nominal values nominal power, W 11 Motor voltage 12 Nominal speed, rpm 3200 Nominal current, A 1.3 nominal torque, N.cm 3.2 No-load values Speed, rpm 4300 Current, A 0.1 Stall values Torque, N.cm 13.5 Current, A 5.2 Performance values Max output power, W 15 Max constant torque, N.cm 1.9 Motor parameters Weight, gr 235 Rotor inertia, gr,cm2 33 Terminal resistance, ohm 2.3 Inductane, mH 2.3 Mech time constant, ms 12 Elec time constant, ms 1 Torque constant, N.cm/A 2.7 Speed constant rpm/N.cm 310 Thanks
Find the transfer function, G(s) = θL (s) / Ea (s), for the motor and load shown below. The torque-speed curve is given by Tm = -8ωm + 200 when the input voltage is 100V. Select the correct option