A small roller in a mechanics setup is pushed by a force F = 4 N as shown in the sketch. The mass of theroller is 0.5 kg8cm4cm3cm 3cmNegleting friction and knowing that the roller is translating only, calculate the normal force at the frontwheel (B).

Answered: Image /qna-images/answer/2a6af92f-537e-4f5a-aeb0-3e155d0f49b4.jpg

A small roller in a mechanics setup is pushed by a force F = 4 N as shown in the sketch. The mass of the roller is 0.5 kg F 8cm 4cm 3cm 3cm Negleting friction and knowing that the roller is translating only, calculate the normal force at the front wheel (B).

A small roller in a mechanics setup is pushed by a force F = 4 N as shown in the sketch. The mass of the roller is 0.5 kg F 8cm 4cm 3cm 3cm Negleting friction and knowing that the roller is translating only, calculate the normal force at the front wheel (B).

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Related questions

Q: is a homogeneous ball of weight N 1000 resting on a smooth wall and resting on B8 an arm of length 5…

Q: 3. The 75-kg chest shown is intended to be moved P= 400 N 15° 一十一 under the condition shown. Does…

Q: 1. A 25-kg box is attached to two light ropes and is being pulled in a frictionless, horizontal…

Q: Tarzan, who weighs 669 N, swings from a cliff at the end of a convenient vine that is 21 m long.…

A: Given data: Weight of Tarzan (w) = 669 N Length of convenient vane = 21 m Strength of vine = 950 N…

Q: ) A(7 kg) block is at position (A) on the track that is (5 m) above the ground. as shown in figure…

Q: k Force Cart I Cart 2 Sensor Mass = M Mass = 3.5M The figure above shows second experimental setup.…

A: After releasing from spring the cart 1 is free to move with some velocity and when it collides with…

Q: A merry-go-round on a playground consists of a horizontal solid disk with a weight of 790 N and a…

Q: Problem 1 a Given: F Н Mass of canister: 4000 kg 30 30° Mass of beam BD: 50 kg BỊ Max allowable…

Q: Q4/ Assuming frictionless motion, compute the force exerted by the arm OA on the cylinder B when 0=…

Q: Mason is is trying to keep a door open using a door stopper. That door is solid, and it has a mass…

A: Solution: As we can see from the figure the net force due to door closer and stopper will be=111.2…

Q: The small piston of a hydraulic lift (g. 1) has a cross-sectional area of 3.00cm2, and its large…

Q: A flypress has two rotating spheres, each of mass 5 kg, fixed to a horizontal arm, s that they are…

Q: A machine part consists of a thin 0.6 m long bar with small 1 kg masses fastened by screws to its…

A: Given data Length of bar = 0.6 m Mass attached at end = 1 kg Maximum force it can withstand = 65 N

Q: QI Block A in the figure below weighs 1.40 N, and block B weighs 4.20 N. The coefficient of kinetic…

Q: A 300 |b block rests on a hortzontal plane. Find the magnitude of the force P required to give the…

A: mg=300×32.2=9660 lb-fts2F=frictional force=μk NF=0.25N

Q: Three friends ride a Ferris wheel with a diameter of 79m. Their combined mas with each car of the…

A: Given Data: The Diameter of a Ferris wheel is (d) = 79 m The Radius of a Ferris wheel is (r) =…

Q: A trolley of mass 101 kg is to be pulled up smooth incline at 15° to the horizontal with an…

Q: Determine the horizontal force required to move a 2500-lb automobile with 23-in.-diameter tires…

A: Given Weight of the automobile = 2500 lb Diameter of the tyre = 23 in Coefficient of rolling…

Q: Q4/ A four wheels drive BMW car accelerating with 6.5 m/s^2 on an inclined pavement with angle of…

A: Four wheel drive carμ=1m=1000kgApplying equations of "newton x-direction" static equilibrium…

Q: 3)The masses of the A and B blocks are mA and mB, respectively. These two blocks are connected by a…

A: first of all we make FBD of both the block , assuming force on the arm is T, and mass A and B moves…

Q: 45. A 2.00 kg block (mass 1) and a 4.00 kg block (mass 2) are connected by a light string as shown;…

A: 45. Given Data: The value of m1 = 2 kg. The value of m2 = 4 kg. The angle of incline is θ=40° The…

Q: A 4.6-kg block is pushed 2.3 m up a vertical wall with constant speed by a constant force of…

Q: As snown Iigure, forces are applied mass of 75 that the coefficient of kinetic friction between the…

Q: Shown in the figure is a 258-kg homogeneous cylinder that slipping on the rolls without horizontal…

Q: A block of mass MA = 40 kg is placed on a wedge and connected by a light string over a massless…

A: Given data: The mass of block A is, MA=40 kg. The mass of block B is, MB=10 kg. The distance…

Q: Q2/ Three blocks having masses of 5 kg , 10 kg and 15 kg are in contact on a fixed smooth inclined…

Q: A plane moves at 820km/h as it makes a horizontal circular turn of radius 15.0 km. a. Draw a free…

Q: 2. A uniform 7 m long table surface with a mass of 20 kg sits on two table legs A and B as shown…

A: The solution of the problem is attached below:

Q: The small piston of a hydraulic lift has a cross-sectional area of 3.00cm^2,and its large piston has…

A: Given

Q: Two boxes of mass m, 3.9 kg and m,=2.3 kg are made of different materials. The boxes in contact are…

A: Given details: m1=3.9kgm2=2.3kgμk1=0.25μk2=0.1θ=28°F=76N

Q: DI II DII B.Y. II 20 kg.mm 10cm 40cm 10cm 10 kg.mm

A: There may be unbalanced forces in any system having a rotating or reciprocating element due to the…

Q: A body has mass 450 g .when it revolves in a circle of radius 2m.The body makes 2 revolution per…

A: It is given that the body made 2 revolutions per second. Thus, the angular velocity of the body can…

Q: A pilot flies an airplane at a constant speed of 870 km/h in the vertical circle of radius 1270 m.…

Q: A single cylinder engine runs at 250 r.p.m. and has a stroke of 180 mm. The reciprocating parts has…

Q: A sled with a mass of 25.0 kg rests on a horizontal sheet of essentially frictionless ice. It is…

Q: The pistons of a 60° twin V-engine has strokes of 120 mm. The connecting rods driving a common crank…

A: Please find the solution below

Q: In the figure below, a force F of magnitude 15 N moves a box of mass m; = 1.5 kg up an incline of…

Q: Problems: Consider a conical pendulum with an 80.0-kg bob on a 10.0-m wire making an angle of 5.00°…

A: As given that mass of the pendulum (m)= 80 Kg and length of the wire= 10 m ; Angle θ=5° with…

Q: A "swing ride" is shown in the figure. For b=1.6 m, L=4.2 m and 0=36° neglect the mass of the cables…

A: Given:-b=1.6mL=4.2mθ=36°m=37kgTo find:-1) Radiys of horizontal circle2) Tension in cable3) Velocity…

Q: highway curve with a radius of 120 m is banked so that there is no lateral pressure on the wheels of…

A: Acceleration: It is nothing but the rate of change of velocity perpendicular to the plane or curve.…

Q: Three objects Mi (60 kg), M2 (40 kg) and M3 (80 kg) are connected by pulleys (negligible mass and…

Q: In the system in which the first starts to move without speed, the masses of 10, 1 kg each, with the…

Q: Q4/ Assuming frictionless motion, compute the force exerted by the arm OA on the cylinder B when e-…

Q: A block of mass 40 kg slides to the right due to the application of the force T. Neglect the mass of…

Q: A 35-kg child rides on a 10-kg bicycle with 500-mmdiameter wheels. Determine the horizontal force…

A: GIVEN : Weight of the child mc=35 kg weight of the bicycle mb=10kg diameter of the wheels d=500mm…

Q: block C mass = 99 kg block D mass = 66kg horizontal force (H) = 555N and is applied at block D.…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A small roller in a mechanics setup is pushed by a force F = 4 N as shown in the sketch. The mass of the
roller is 0.5 kg
8cm
4cm
3cm 3cm
Negleting friction and knowing that the roller is translating only, calculate the normal force at the front
wheel (B).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
Determine the smallest force P, applied to the plunger D, that will prevent the couple C=200Nm from moving the cylinder. Friction may be neglected at all surfaces, except between the plunger and cylinder. The masses of the bodies are negligible.
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a) Determine the force P required to pull the roller at a constant speed. (b) What force P would be needed to push the roller at a constant speed?
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The uniform ladder of weight W is raised slowly by applying a vertical force P to the rope at A. Show that P is independent of the angle .
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
A cylinder of mass M and radius R is rotated in a uniform V groovewith constant angular speed ω. The coefficient of friction betweenthe cylinder and each surface is μ. What torque must be applied tothe cylinder to keep it rotating?