A small turbine, shown in Fig. P 4.48, is operated at part load by throttling a 0.25 kg/s steam supply at 1.4 MPa, 250°C down to 1.1 MPa before it enters the turbine and the exhaust is at 10 kPa. If the turbine produces 110 kW, find the exhaust temperature (and quality if saturated). 1. 2 3.

A small turbine, shown in Fig. P 4.48, is operated at part load by throttling a 0.25 kg/s steam supply at 1.4 MPa, 250°C down to 1.1 MPa before it enters the turbine and the exhaust is at 10 kPa. If the turbine produces 110 kW, find the exhaust temperature (and quality if saturated). 1. 2 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can you please solve this for me, thanks. 10 kg/s of steam (H2O) enters a turbine at 10 m/s and a specific enthalpy of 3500 kJ/kg and leaves at an outlet 10m below the inlet with a specific enthalpy of 2500 kJ/kg and a velocity of 20 m/s. Assume steady-state steady-flow. If the heat lost from the turbine is 20% that of the turbine work, determine a.) the turbine horsepower. If the turbine is coupled to a generator with a 90% electrical efficiency, and the turbine horsepower has an 80% mechanical efficiency, b.) how much income will a power plant generate in one year if the electrical energy is sold at PhP 3.51 per kW-hr? (Hint: Mechanical efficiency = actual turbine work / ideal turbine work. Electrical efficiency of a generator = electrical output / actual turbine work.)
A turbine, operating under steady- flow conditions, reccives 1000 kg/min of stcam. At the inlet, the pressure is 30 bar, the temperature is 400°C, the velocity At the exit, the pressure is 0.7 bar, the quality is (100%), and the velocity is 100 m/s. If the turbine produced a power output of 9300 KW. By using the energy balance of open system with sutable tables, answer the following: (a) What are the main assumptions ? (b) Calculate dh, AKe ? (c) Calculate the rate of heat transfer between the turbine and surroundings, in kW.
A twin-cylinder, double- acting, compressor with a clearance of 5% draws in oxygen at 450 kPa, 17°C, and discharges it at 1800 kPa. The mass flow rate is 20kg/min, compression and expansion are polytropic with n= 1.25. Find (a) the work, (b) the heat transferred, and (c) the bore and stroke for 100 rpm and L/D= 1.20. Answer: (a) -40.23 kW, (b) -829 kJ/min (c) 21.71 x 25.76 cm
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
A twin-cylinder, double-acting,compressor with a clearance of 5% draws in oxygen at 450 kpa,17c and discharges it at 1800 kpa. The mass flow rate is 20 kg/min, compression and expansion are polytropic with n=1.25. Find (a) the work,(b)the heat transferred and (c) the bore and stroke for 100 rpm and L/D =1.20. Ans (a)-40.23 kw, (b) -829kj/min / (c)21.71x25.76 cm
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP?
A double-acting compressor with c= 7% draws 40 lb per minute of air at 14.7 psia and 80°F and discharges it at 90 psia. Compression and expansion are polytropic with n= 1.28. Find (a) the work, (b) the heat rejected, (c)the bore and stroke for 90 rpm and L/D= 1.25.
A single stage air compressor handles of atmospheric pressure air and delivers it to a receiver at 652.75 kPa and flow rate of 0.0705 m3 /sec. Its volumetric efficiency is 0.72, its compression efficiency on an isothermal basis is 0.85 and its mechanical efficiency is 0.90. If it rotates at 350 rpm, what power in kW is required to drive it?
an air flow is brought from 20 degree celsius, 100 kPa to 1000 kPa, 330 degree celsius by an adiabatic compressor driven by 50 kW motor. what are the mass flow rate and the exit volume flow rate of air?
Steam enters a turbine at 10 MPa and 600°C and exits at 0.1 bar. If the isentropic turbine efficiency is 90%, find the following:a. Specific actual and isentropic turbine workb. Actual and isentropic turbine exit temperature
The power required for the compressor, to handle air adiabatically from 101.325kPaa and 300 °K to 305 kPaa, 2550 Hp. The inlet velocity is 21 m/s and the dischargevelocity of air is 85 m/s. a) If the process is isentropic, find the volume of air handles,in lps, measured at inlet conditions. b) If the compression is irreversible adiabatic totemperature 157.5 °C, with the capacity obtained in a), find the power input.
Please show your complete solution. Thank you! During the reversible process executed by the non-flow system, the pressure increases 334.79 kPa to 1378.96 kPa in accordance with PV=C and the internal energy increase is 22, 577 J, the initial volume is 85 liters. Find the heat.