A soft drink (mostly water) flows in a pipe at a beverage plant with a mass flow rate that would fill 220 0.355-L cans per minute. At point 2 in the pipe, the gauge pressure is 152 kPa and the cross-sectional area is 8.00 cm2. At point 1, 1.35 m above point 2, the cross-sectional area is 2.00 cm². FIND: • flow speeds at points 1 and 2 [Select] • gauge pressure at point 1 [Select] ►

A soft drink (mostly water) flows in a pipe at a beverage plant with a mass flow rate that would fill 220 0.355-L cans per minute. At point 2 in the pipe, the gauge pressure is 152 kPa and the cross-sectional area is 8.00 cm2. At point 1, 1.35 m above point 2, the cross-sectional area is 2.00 cm². FIND: • flow speeds at points 1 and 2 [Select] • gauge pressure at point 1 [Select] ►

Name: 62 A soft drink (mostly water) flows in a pipe at a beverage plant wit
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: 62 A soft drink (mostly water) flows in a pipe at a beverage plant with a mass flow rate that would fill 220 0.355-L cans per minute. Atpoint 2 in the pipe, the gauge pressure is 152 kPa and the cross-sectional area is 8.00 cm2. At point 1, 1.35 m ab

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 105AP: Water towers store water above the level of consumers for times of heavy use, eliminating need for...

See similar textbooks

Similar questions

Gasoline is piped underground from refineries to major users. The flow rate is 3.00102m3/s (about 500 gal/min), viscosity of gasoline is 3.00102m3/s , and its density is 680 kg/m3. (a) What minimum diameter must be pipe have if the Reynolds number is to be less 2000? (b) What pressure difference must be along each kilometer of be pipe to maintain flow rate?
Prove the sped of an incompressible fluid through a constriction, such as a Venturi tube, increases by a factor equal to the square of the factor by which the diameter decreases. (The converse applies for flow out of a constriction into a larger-diameter region.)
What is the difference between flow rate and fluid velocity? How are they related?
How would you determine the density of an irregularly shaped rock?
(a) Convert normal blood pressure readings of 120 over 80 mm Hg to newtons per meter squared using be relationship for pressure due to the weight of a fluid (p=hg) rater a conversion factor. (b) Explain why be blood pressure of an infant would likely be smaller than that of an adult. Specifically, consider the smaller height to which blood mast be pumped.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.
How much pressure is transmitted in the hydraulic system considered in Example 11.6? Express your answer in pascals and in atmospheres.
Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Verify that work input equals work output for a hydraulic system assuming no losses due to fiction. Do this by showing that distance output force moves is reduced by the same factor output force is increased. Assume the volume of the fluid is constant. What effect would friction within the fluid and between components in the system have output force? How would this depend on whether or not fluid is moving?