Subject: algebra A soft drink with the properties of 10 °C water is sucked through a 3.9-mm-diameter, 0.25-m-long straw at a rate of 3.6 cm³/s. (a) Is theflow at the outlet of the straw laminar? (b) Is it fully developed? To explain calculate (c) the Reynolds number and (d) the entrancelength.(a) laminar flow(b) fully developed(c) Re-i 898.16(d), 0.175m

Answered: Image /qna-images/answer/933c18ca-c75a-483d-a250-ad844f32083d.jpg

Answered: A soft drink with the properties of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fluid at 20C flows at 850 cm3/s through an 8 cm diameter pipe. Determine the entrance length if the fluid is (a) hydrogen; (b) air; (c) gasoline; (d) water; (e) mercury; and (f) glycerin.
Crude oil of density 925 kg/m3 and absoluteviscosity 0.065 N-s/m2 at 20oC is pumped through ahorizontal pipeline 100 mm in diameter at a rate of 10 L/s.Determine the head loss in each kilometer of the pipeline.What power is supplied by the pump per kilometer length?
Water is pumped upwards from a 0.5 m diameter bed consisting of iron oxide particles with a density of 5300 kg / m3 with a diameter of 1mm. If the bed porosity is 0.45, what is the required velocity for the bed to flow?
Water at 20 ° C flows steadily through the piping junction inFig. P3.32, entering section 1 at 20 gal/min. The averagevelocity at section 2 is 2.5 m/s. A portion of the flow isdiverted through the showerhead, which contains 100 holesof 1-mm diameter. Assuming uniform shower flow, estimatethe exit velocity from the showerhead jets.
A horizontal pipe bend with a deflection angle of 120o has an entrance diameter of 300 mm and exit diameter of 100 mm. Oil with a density of 860 Kg/m3 enters at the rate of 3.6 m/s and at a pressure of 180 KPa. Determine the magnitude of the force required to hold the bend in place for (a) smooth flow; (b) a situation where head loss is 0.05(v100-v300) 2/2g.
The reservoirs in Fig. are connected by cast iron pipesjoined abruptly, with sharp-edged entrance and exit. Includingminor losses, estimate the flow of water at 20 °C if the surfaceof reservoir 1 is 45 ft higher than that of reservoir 2.
(Restrictions on Bernoulli equation) A 0.256-m-diameter soccer ball, pressurized to 20.3 kPa, develops a small leak with an area equivalent to 0.006 mm2. If viscous effects are neglected and the air is assumed to be incompressible, determine the flowrate through the hole. m3/sWould the ball become noticeably softer during a 1-hr soccer game? YesNoIs it reasonable to assume incompressible flow for this situation? NoYes
1. A research experiment requires a laminar flow of water at 20°C through a 120mm diameterpipe at a Reynolds number of 1992.A. What is the average velocity?B. What maximum velocity is to be expected?C. What would be the pressure drop over a 11m horizontal length of developed flow? Useρ= 1000 kg/m3and v=1x10-6m2/s.D. How long would the entrance region be?
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
Fluid of constant density is flowing at a velocity of 0.5 meter per second into a horizontal nozzle of decreasing cross-section. The velocity of water ,in meter per second, going out of the nozzle if the diameter at the exit point is 1/3 the diameter in the entry point is
Consider an air solar collector that is 1 m wide and 4 m long and has a constant spacing of 3 cm between the glass cover and the collector plate. Air flows at an average temperature of 45°C at a rate of 0.12 m3/s through the 1-m-wide edge of the collector along the 4-m-long passageway. Disregarding the entrance and roughness effects and the 90° bend, determine the pressure drop in the collector.
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS