A soil has the following particle-size distribution: Soil A Soil B Soil C Gravel 20% 2% Sand 10% 67% 50% Silt 30% 23% 8% Clay 40% 10% 40% Classify the soil according to USDA textural classification system.

A soil has the following particle-size distribution: Soil A Soil B Soil C Gravel 20% 2% Sand 10% 67% 50% Silt 30% 23% 8% Clay 40% 10% 40% Classify the soil according to USDA textural classification system.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter4: Soil Classification

Section: Chapter Questions

Problem 4.6CTP: For soils that are classified by the following USCS symbols, what would be the most likely AASHTO...

See similar textbooks

Related questions

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

Q: Why is it important to calculate stress in beams?

A: The stresses are produced in beams when they are subjected to loadings. The stresses that are…

Q: Calculate the volume and surface area of a solid cylinder 1.5 m diameter and 2.5 m tall.

A: Given- Solid cylinder-Diameter d=1.5 mHeight h=2.5 m

Q: 1. A total of 5,000 person-trips are made between a commercial district and a residential area…

A: Uk = -0.5 T1 - 0.5 T2 - 2.00 C For Private Automobile ; T1 = 10 , T2 = 5 and C = 5.00 Uk = -0.5 (10)…

Q: The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a…

A: Using Muller Breslau principle draw the ILD for Shear at E. Then place the loads such that the value…

Q: Consider a regime channel having a discharge of 50 m3/s and silt factor 1.10. The hydraulic radius…

Q: The extruded plastic shape will be subjected to an internal shear force of V-385 lb. Dimensions of…

A: V = 385lb

Q: D F 6ok F 10 KA 10 10 Fimure P-7 tel

Q: The axial load 210 kN applied to the lap joint is distributed equally among the three 16.5-mm-…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: ASKED: To determine the largest moment M that can be applied to the beam corresponding to the…

Q: 2. Another reinforced concrete beam has the following properties: • fy= 60 ksi • f= 5,000 psi • As =…

Q: w kN/m В A

A: Given data:

Q: A field unit determination test for the soil, yielded the following data. Moisture content = 12% and…

A: The moisture content of soil in lab, w=12%The moist unit weight of soil in lab, γb =106 lbft3The…

Q: Given: With the passing distance, sighted on a certain highway to be 461 mts., the following data…

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

Q: A tension force generates a greater stress than an equivalent compression force. (A) True B) False

Q: PROBLEM 03: Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes…

Q: The bell-crank mechanism is in equilibrium for an applied load of F, = 19 kN applied at A. Assume a…

Q: Determine the reaction at B in kN. 45 kN/m 30 kN/m 30 kN/m 60° 810 kN-m 3.6 m 3.6 m

Q: Solve 5 problems (following the conditions stated below) involving the use of shear and moment…

A: Note : since you have posted multiple problems, as per your choice, I solve 1st problem for you.…

Q: b1 Answer: 1= i 648.03 N-m Save for Later Last saved 2 hours ago. Attemnt

Q: why does recreation trip/travel from city to another city is lower time and inconvenience…

A: Normal travelling in between two points and recreational type of travelling are so much different…

Q: in., a = 3.3 in., and t = 0.8 in. For a vertical shear torce surface at B. d В b Answer: i 0.685…

Q: D 3 ft E B C 5 ft A - 4 ft- -6 ft-

Q: Present a solution to a problem that lies within the domain/area of engineering modelling and…

A: Changes in design are common. It would be wonderful if we could completely eliminate change orders.…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 305 lb. Dimensions of…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 800 mm.…

Q: ЗР Strain gage 1.1, a a H Answer: P = i 369 N

Q: ANSWER 22 AND 23

A: To find space mean speed

Q: y t (typ.) d V b swer:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 680 mm.…

A: The length of beam, L=680mm=6.8mThe dimesions of rectangular beam are b1=33mm, d1=93mm, b2=20mm,…

Q: A beam is subjected to equal bending moments of M, = 3000 N-m. The cross-sectional dimensions are b…

A: Given : Applied bending moment, Mz = 3000 N-mCross-sectional dimensions are : b = 190 mm, c = 30 mm,…

Q: The beam is loaded as shown. which of the following nearly givės the flexural stress due to…

Q: the titrimetric determination of water hardness. Why?

A: In a hardness test , a titrant of EDTA is added in small amount in titration. On addition of EDTA…

Q: A horizontal 150mm diameter pipe gradually reduces its section to 50mm diameter, subsequently,…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: 1. When two grades meet at the valley and the curve will have a convexity downwards. a. Summit b.…

A: As per company's guidelines we can only answer first three questions. Kindly post other questions as…

Q: 2-29. Determine the reactions at the supports A. B, C, and D.

Q: Determine the reduced live load supported by a typical interior

Q: During a test on a 2.4-m suppressed weir 900mm high, the head was maintained constant at 300 mm. In…

Q: The rectangular piece of wood, 56 mm by 183 mm, is used as a compression block. The grain of the…

A: Concept used:- Stress= force per unit area. Given:- Angle of grain = 32.3 deg Allowable stress in…

Q: What is the significance of computing deflections in beams?

A: The displacement of a beam or junction from its initial position owing to the forces and loads…

Q: Quiz No. 1 (Truss) Given the Truss as shown below with load P1 = X N and P2 = 3X N. Using Method of…

Q: A glass (SG = 2.6) is filled to a depth d with linseed oil (SG=0.92) and allowed to float in a tank…

Q: 2-34. Determine the components of reaction at the supports. Joint Cis a rigid connection. 8 kN 6 KN…

Q: The trolley AB carrying a 80-kN load travels on the 15-m-long beam. De- 4.47 termine the maximum…

Q: The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel in…

Q: Between a plate and the body of a bolt or a pin, the average bearing stress is computed by dividing…

A: Bearing stress may be defined as the contact pressure between the seperate bodies

Q: Problem 1. Use double integration method to find the slope at the left of hinge at B and the…

A: Calculation of slope ( left) and deflection at B###

Q: INSTRUCTIONS: Solve the sample problem below related to Moving Loads. A truck with axle loads of 100…

Concept explainers

Soil classification and characteristics

Soil classification is a method of categorizing soil based on its properties, types, and uses. The motive of soil classification is to arrange various types of soils and divide them into groups for various engineering and agricultural purposes. Soil classification is carried out by various agencies as per their purposes. From an engineering perspective, soil classification is done to find out the suitability of soil for various construction purposes like the construction of dams, foundations, highways, infrastructures, and so on. For engineering purposes, the soil is classified by the following systems:

Question

PROBLEM No. 1
A soil has the following particle-size distribution:
Soil A
Soil B
Soil C
Gravel
20%
2%
Sand
10%
67%
50%
Silt
30%
23%
8%
Clay
40%
10%
40%
the soil according to USDA textural classification system.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For soils that are classified by the following USCS symbols, what would be the most likely AASHTO symbols? (Reference: Liu, 1970) Gravels: GW, GP, GM, GC Sands: SW, SP, SM, SC Fines: ML, CL, MH, CH
Situation 1 – Refer to Figure. Classify the soil according to the USDA textural classification system. The soil has particle size distribution of Gravel – 21% Silt – 35% Sand – 12% Clay – 32% 1. Calculate the modified percentage of sand 2. Compute the modified percentage of silt 3. What is the classification?
A soil has the following particle size distribution Gravel = 20% Sand = 10% Silt = 30%mm Clay = 40% Classify the soil according to USDA textural classification.
The soil has the following particle-size distribution Gravel – 20%, Sand – 10%, Silt, 30%, Clay, 40%.Classify according to USDA textural classification system.
If soils cumulatively retained on sieve #4 is 68%, then the percentage of soil classified as sand, silt, and clay is:
Classify the soil according to the soil classification system AASHTO: With the following data: Percentage passing: sieve No. 200 = 45% sieve No. 40 = 10% sieve No. 10 = 45% LP = 32 LL = 54
Classify the following soils by the AASHTO classification system. Description Soil A Soil B Soil C Percent finer than No.10 sieve 83 100 48 Percent finer than No.40 sieve 48 92 28 Percent finer than No.200 sieve 20 86 6 Liquid Limit 20 70 - Plasticity Index 5 32 Nonplastic
A soil sample having no particles larger than the No. 4 sieve is classified as a sandy silt, ML, by the Unified Soil Classification System ( LL = 29% ; PI = 5% silt particles comprise 70% of the sample, sand 15%, and clay 15%). What is the probable soil classification in the AASHTO system? In the U.S. Department of Agriculture textural system?
Classify all the soils in 5.8 using unified soil classification system. Give group symbols and the group names
For an inorganic soil, the following grain-size analysis is given:Sieve No. % Passing4 10010 9020 6440 3880 18200 13For this soil, LL = 23% and PL = 19%. Classify the soil according to:a. The AASHTO soil classificationb. The Unified soil classification system
Calculate the shrinkage ratio and specific gravity of the soil solids having following quantities. 1. Soil having initial sturated volume and final dry volume 28.5 cm3 and 18.5 cm3 respectively. 2. Soil having initial saturated mass and final dry mass 48g and 35g reepectively and shrinkage limit is 18.4. A) 1.89, 2.89 B) 1.95, 2.95 C) 1.97, 2.97 D) 1.71, 2.71 make it fast
Given the soil particle distribution. Gravel- 20% Sand- 15% Silt- 20% Clay- 45% Calculate the modified percentage of sand.