Answered: A solid circular bar is acted upon by…

A solid circular bar is acted upon by tensile force of 20N. The diameter of circular Bar is 10 mm. The change in length of bar is 0.2 m, Original length is 10 m. Determine stress and strain produced

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Related questions

Q: A bar is compressed to half of its original length. Determine the magnitude of true strain produced…

Q: Can the normal strain on the free surface of a body be measured in aparticular direction using an…

A: The magnitude of the strain measures using the device strain gauge. Strain gauge works on a…

Q: A load of 20 kN is applied to a rod with a diameter of 12.5 mm. Calculate the strain in the rod if…

A: Given Data: The load applied, P=20 kN Diameter of the rod, d=12.5 mm Young's modulus, E=103 GPa

Q: For a steel sample under tensile testing, if the first principal strain was equal to 0.005 and all…

A: In continuum mechanics, Lamé parameters (also called the Lamé coefficients, Lamé constants or Lamé…

Q: Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: A small room is made up of rectangular metal bars. One bar has a width of 10 mm and would be able to…

A: Given:w=10 mmσc=20 MPa

Q: Two round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and…

A: Given that, Esteel=20×1010PaEbrass=10×1010Pa

Q: A bar is compressed to half of its original length. Find the magnitude of true strain produced in…

Q: If Pi=20,000 lb & P2=50,000 lb, determine the strain energy of the rod. Evaluate whether this value…

Q: 8. A copper wire of diameter 0.80mm fails at an Engineering stress 248.2MPA. Its ductility is…

Q: 5) In open die forging, a disc of diameter 200 mm and height 60 mm is compressed without any…

A: Given:- initial diameter do=200 mm initial height,ho=60 mm Final…

Q: 6.A metal rod 150cm long and of diameter 2cm is subjected to an axial pull of 20KN. What will be the…

Q: A rod is 0.5 m long and 5 mm diameter. It is stretched 0.06 mm by a force of 3 kN. Determine the…

Q: A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter.…

Q: Q2/ A metal rod of cross-sectional area 100 mm 2 curries a maximum tensile loud of 20 kN. The…

A: Suppose a normal load 'P' is applied on a rod having cross-sectional area 'A' and modulus of…

Q: . In a tensile test of a cylindrical specimen with an initial diameter of 12 mm, the loads at 15 and…

A: Given…

Q: A bar produces a lateral strain of -70 × 10-5 when subjected to tensile stress of magnitude 400 MPa…

A: Given, Lateral strain = εl = -70 x 10-5 Tensile axial stress = σ = 400 MPa Poisson's ratio = μ = 0.3…

Q: Find the value of strain if stress is 55 N/mm2 and elasticity is 10000 N/mm2

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

Q: A cylindrical bar of metal having a diameter of 18.8 mm (A=278 mm^2) and a length of 198 mm is…

A: Bar diameter, d=18.8mm=0.0188m Cross sectional area of the bar, A=278mm2=0.000278 m2 Length of the…

Q: A light wire 1.75 m long has a cross-sectional area of 2.3 mm². It is hung vertically and stretches…

A: hookes law states that stress is directly proportional to Strain. Youngs modulus = Stress/Strain…

Q: A steel bar is stressed to 280 MPa. The modulus of elasticity is 205 GPa. The bar is 80 mm diameter…

A: Given data : Length (L)=240 mm Modulus of elasticity (E)=205 GPa Diameter (d)=80 mm Stress (σ)=280…

Q: A tension specimen of circular cross-section tapers uniformly from 20 mm to 16 mm diameter over a…

A: given; for tapered bar;diameter(d1)=20mmdiameter(d2)=16mmgauge length(l)=200mmaxial load(P)=40KN…

Q: Find the value of strain if initial length of rod is 100 m and change in length of rod due tensile…

A: Given data : Initial length of rod=L Change in length of rod=∆L Required : Strain

Q: A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is…

Q: Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum…

A: Given, A compound axial member made of Aluminum and copper Diameter of the axial member, d=1.45 in.…

Q: If longitudinal strain for a wire is 0.03 and its Poisson's ratio is 0.5, then its lateral strain is

Q: When a tensile load of 20kN is applied to a rod of length 5 cm, the strain is 0.05. The change in…

Q: Draw a structure which satisfies plane strain condition

A: Plane strain is state of strain, when strain normal to the x and y plane is zero. Also shear strain…

Q: Find the value of strain if stress is 4 N/mm2 and elasticity is 10000 N/mm2

Q: n of aluminum having a rectangular cross section 9.6 mm × 13.0 mm (0.3780 in. × 0.5118 in.) is…

A: Given:Area, A=9.6*13.0 mm2F=35800 NE=69 GPa

Q: A composite bar is subjected to a tensile load of 115 kN. Bar 1 is rectangular cross section with…

Q: A steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and…

Q: PROPAGATION OF ERRORS Determine the range of values to which the strain will be calculated. F =…

Q: An element of bone in plane strain where the state of strain are = 12 x 10-4). Find (a) the stresses…

A: Given Data εx=8×10-4 εy=5×10-4γxy=12×10-4 μ=v=0.3 E=2×109 N/m2

Q: Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa

A: Given data : Stress σ=30 MPa Modulus of elasticity E=65 MPa To find : Strain

Q: A mild steel specimen of Diameter 9 mm, Length 16 cm is subjected to tensile load and it is found…

Q: Find the value of strain stress=30 MPa Modulus of elasticity=65 MPa

A: The value of Strain is ε = 0.4615.

Q: A tensile stress is to be applied along the long axis of a cylindrical brass and that has a diameter…

Q: A metal bar 5.0 m long extends by 0.05 m when a load is applied to it. The strain is?

A: Given that, Length of the metal bar, L = 5 m, Change in length of the bar after applying load,…

Q: At the proportional limit, the axial load of a 0.70-in- diameter bar was 5400 lb. A 2.20-in. gauge…

Q: The poisson's ratio for a homogeneous bar is V3. If the bar is subjected to a tensile load, the…

Q: What strain will be produced by a stress of 80 x 106 N/m2, for a given modulus of elasticity 200GPa.…

A: Given, stress = 80 x 106 N/m2 modulus of elasticity (E) = 200GPa= 200x 109 N/m2

Q: A rod of length 40 mm is stretched to make a rod of length 60 mm. It is compressed to make a rod of…

Q: specimen of a metal 75 mm long was stretched with a force of 10 kN. The strain produced in the…

Q: Determine Stress and strain Draw the stress strain diagram Determine the following mechanical…

A: a) Please refer the following table for stress and strain calculations. Calculations are done using…

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

Quickly

A solid circular bar is acted upon by tensile force of 20N. The diameter
of circular Bar is 10 mm. The change in length of bar is 0.2 m, Original
length is 10 m . Determine stress and strain produced

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?
A metal bar 5.0 m long extends by 0.05 mm when a tensile load is applied to it. The percentage strain is:
A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s modulus of the material of the rod is 2 x 105 N/mm2, Calculate :(i) stress (ii) strain and (iii) the elongation of the rod.
A small room is made up ofrectangular metal bars. One bar has a width of 10 mm and would beable to withstand a maximum compressive stress of 20 MPa.i. Prove that, the minimum breadth of this bar can withstand a burdenedwith a force of 3 KN.ii. If the bar in question is 2 m long and decreases in length by 0.25 mmwhen a force is applied, then show that a percentage strain can beobtained.iii. What would be its Modulus of Elasticity, E?
A steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and 240 mm long. Determine the following I) the strain 2) the force
A metal wire is 2.5 mm diameter and 2m long. A force of 12 N is applied to it and it stretched 0.3 mm. Determine the stress, strain and tensile modules of the wire.
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
A mild steel rod of 12mm diameter was tested for tensile strength with the gauge length of 60mm. After the test final length and the final diameter were 80mm and 7mm, respectively. Find the strain in the transverse direction
A cylindrical bar of metal having a diameter of 18.8 mm (A=278 mm^2) and a length of 198 mm is deformed elastically in tension with a force of 49400 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34, respectively, determine the amount by which this specimen will elongate (in mm) in the direction of the applied stress.
The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius of the wire is 0.5 mm. Find the stress, strain and young's modulus of material of the wire. Draw a free body diagram.
When a homogeneous isotropic material is subjected to a state oftriaxial stress, the strain in each direction is influenced by thestrains produced by all the stresses.how?