A solid constant-diameter circular shaft is subjected to the torques of TA = 470 lb-ft, TB = 1030 Ib-ft, Tc = 850 lb-ft, and TD = 290 lb-ft, %3D acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 4400 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp B D Answer:

A solid constant-diameter circular shaft is subjected to the torques of TA = 470 lb-ft, TB = 1030 Ib-ft, Tc = 850 lb-ft, and TD = 290 lb-ft, %3D acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 4400 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp B D Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque TC that can be applied to the shaft.
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70048581 Pa and angle of twist of 2.29ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.01 m, and y = 1.69 m. Round off the final answer to two decimal places.
A man exerted a force of 60 lbs at B as shown in the figure. Compute the angle theta in degrees. Compute the tension of the cable CAD in lbs.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Q1) For the force system shown in figure, 1) Find the angle (¢) so that the resultant of these forces will be vertical. 45 kN S5 kN 3m
Compute the value of EIy at 2.5 m from the left support.
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m) a) Show the support reactions and load occurring on the rod. b) Do you calculate support reactions? c) Calculate the Normal Force, Shear Force and Moment values by cutting from the points you have determined. d) Draw cross-section impact diagrams? Do you specify the maximum positive and negative moment values? e) Check the cross-sectional influence diagrams with a simple method, briefly explain the control steps.
The compound shaft shown consists of a solid shaft AB made ofbronze [G = 40 GPa], and a solid shaft BC made of steel [G = 85 GPa].The compound shaft is subjected to torques TB = 700 N.m at point B,and TC = 200 N.m at point C, acting in opposite directions.[LAB = 900 mm, LBC = 1200 mm, dAB = 35 mm, dBC = 25 mm]Determine (a) the internal torques in shafts AB and BC, (b) the shearstresses in shafts AB and BC, and (c) the angle of twist at point C.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
Determine the following unknowns on the beam shown below using Conjugated-Beam Method. Consider 250 mm x 250 mm Section and E = 200 GPa. Note: a = 4.5 m b = 33.0 kN/m c = 13 kN Find the following A. Vertical reaction at C in kN. B. Moment reaction at C in kN-m. C. Deflection at point B in mm. D. Maximum deflection on the beam in mm.
Determine the Force Frequired to hold the bar AB in a horizontal position on the smooth inclines shown in figure below. Also determine the reactions at A and B 1.2m, 4.2m, 0.6m A 60 degrees and 45 degrees B 90N