A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with the help of open die forging. The work material characteristics are represented by k = 350MPA and n = 0.16. If coefficient of friction is 0.1, find the %3D maximum forging force.

A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with the help of open die forging. The work material characteristics are represented by k = 350MPA and n = 0.16. If coefficient of friction is 0.1, find the %3D maximum forging force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Calculate the moment created by Fabout the origin using a scalar method of your choice. Express the ...

Q: An Atwood's system consists of two pulleys and two loads with equal masses m. The first pulley, fixe...

A: First, we write the equation of motion for both the masses.

Q: A 64-kg woman holds a 7-kg package as she stands within an elevator which briefly accelerates upward...

A: Given:M=64 Kgm=7 Kga=0.29g

Q: A spark ignition engine of a compression ratio of 8 , operates with stoichiometric fuel-air ratio of...

A: Given: compression ratio r=8 P1=1 atmosphere and T1=350 K residual gas fraction f=0.08 and the exha...

Q: Air enters a compressor operating at steady-state at 1 atm with a specific enthalpy of h1 = 224 kJ/k...

Q: ) Consider the masses A and B with weight as shown. If the two systems are released from rest, which...

Q: AF2 AF, AF DAz AF

Q: An orifice of 0.1-meter-diameter is installed in a pipe having a diameter equal to 0.3 meters as sho...

A: The given values are - A0=π40.12=7.85×10-3 m2 A1=π4(0.3)2 = 0.071 m2 Cd=0.63 Pressure head (h) = P...

Q: In a single pass drilling operation, a through hole of 15mm diameter is to be drilled in a steel pla...

Q: PROBLEM 1: Estimate the kilowatt pump you would need to pump 450 Liter/min of liquid water at 20°C t...

Q: Steam at 200 deg. C and with isothemally to 0.515 Mpa. For 5kg. Find : a. As, AH, AU b. Q an entropy...

Q: Water (C, = 4.18kJ/kg K) at 80°C enters a counter flow heat exchanger with a %3D mass flow rate of 0...

Q: Determine the constraint equation which relates the accelerations of bodies A and B.Assume that the ...

Q: ) A 5 lb ball is attached to a 3 ft long rope and it rotates in a vertical circular path at a consta...

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear stress...

Q: 2. The frame shown in the figure is supported by a pin at point A and a roller at point E. Determine...

Q: Question 1 In the strength of material, the section of the body involved is taken into consideratio...

A: 1) Given that an object is having a force which has a cross section area. Then by the definition - ...

Q: A uniform bar AB weighing 500 kg is supported at both end by cable as shown in the figure below. Det...

Q: A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maxim...

Q: nozzle from 1500 kpa , 288 deg. C Steam plows isentropically throngh 966 k Pa . For 454 gls determin...

A: Given Temperature, T1 = 288oC = 561 K Pressure, P2 = 960 kPa P1 = ...

Q: Replace the forces and couple system acting on the T member with an equivalent force couple at A. Ex...

A: Given data: Horizontal force=50 N Need to determine the equivalent force at A.

Q: An ideal Otto cycle has a compression ratio of 6. At the beginning of the compression process, air i...

Q: 147 Find the volumetric efficiency and estimate the approximate clearance of 45.75 x 45.75-cm, doubl...

Q: In the selection of the ram of a pile driver, it is desired that the ram lose all of its kinetic ene...

Q: The The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loa...

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inner and outer rad...

A: Write the given values with the suitable variables. ri=120 mm=0.120 mro=250 mm=0.250 mμ=0.25W=20 kN=...

Q: A barge is pulled by two tugboats. If the tension force in the rope TAB and TBC is 3500 Ibs and 2500...

A: Given Data TAB= 3500 lbs TAC=2500 lbs

Q: Compute the hydrostatic force. Oil, SG 0.83 3m I m Gate 2m 50 B.

Q: ulate the reaction forces Ay and MA acting on the beam

A: we will use equilibrium conditions to solve for the values

Q: * The governing equations of a mass-spring vibrating system with two masses are: yi' = -2y1 - y2 y" ...

A: Given : To find : Frequencies and relative displacements

Q: What are the accreditation required in specialized engineering field

A: The accreditation required in specialized engineering field :- Program Educational objectives :- Pr...

Q: Problem 1: Water at 10°C is flowing at 0.075 m*/s. Calculate the weight flow rate and the mass flow ...

Q: Water (C, = 4.18kJ/kg K) at 80°C enters a counter flow heat exchanger with a mass flow rate of 0.5kg...

A: Givencounter flow heat exchangerTw1=80oCCpw=4.18kJ/kgKmw=0.5kg/sCpa=1kJ/kgKTa1=30oCma=2.09kg/seffect...

Q: Steam ot 200 deg. C and with an entropy OF 5. 6105 kjlkg-k exponds isothermally to 0.515 Mpa. For 5k...

Q: Neglect the diameter of the small pulley attached to body A and determine the magnitude of the total...

Q: Experimental results: R flywheel Axle circumference, C = 2ar (m) аxle Axle radius, r (m) Critical ma...

A: Givenh=1.61mtavg=6.3secR=0.125mmf=1.7kgM=2kg

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown...

A: To know the variation and maximum value of shear force and bending moment, V and M diagram are drawn...

Q: Find logarithmic mean temperature difference ?

A: Given; A counter flow heat exchanger with a mass fow rate,m=0.5 kg/sWater; cP=0.5 kg/s t=800 CAir;...

Q: An ideal Diesel cycle has a compression ratio of 18. Air is at 27°C and 100 kPa at the beginning of ...

Q: Two identical 1350-kg automobiles A and B are at rest with their brakes released when B is struck by...

Q: Calculate the lattice constant of the alloy you found in part (a). Assume the alloy and its end memb...

A: Given data, The alloy is Zinc Blende (ZnS) Atomic radius of ZnS, aZnS=5.409 A° To determine, the lat...

Q: Task 2.2 A large pressure vessel contains air in state 1 (pi = 3 bar, T1 = 360 K, c1 = 0 m/s). The a...

A: Given: At state 1p1=3 barT1=360 Kc1=0 m/sηsD=0.9State 2:p2=1 barA2=0.1 m2

Q: 1. The working substance for a Carnot cycle is 8 lb of air. The volume at the beginning of isotherma...

Q: In a single pass drilling operation, a through hole of 15mm diameter is to be drilled in a steel pla...

Q: An elastic member 16.6 mm thick is glued in between two rigid members. Considering a shear force of ...

Q: a given point in a flow field or air, Mach number, velocity, and density are 0.9, 300 mps, and 1.2 k...

A: we have to determine the dynamic pressure of this flow

Q: If le is the mass moment of inertia of a rigid body with respect to an axis passing through its cent...

Q: A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with th...

Q: Saturated steam at 100 bar pressure is expanded through a throttle valve to an exit pressure of 1 ba...

Q: In the example case of radiator, to enhance heat transfer from hot water to air, the effective metho...

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A solid piece of steel 60 mm in diameter
and 80 mm height is reduced in height by
50 percent with the help of open die
forging. The work material characteristics
are represented by k = 350MPA and n =
0.16. If coefficient of friction is 0.1, find the
maximum forging force.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 300mm thick slab is being cold rolled using roll of 600mm diameter.If the coefficient of friction is 0.08. Determine the maximum possible reduction.
A cylindrical part with initial diameter of 45 mm and the initial height of 40 mm is upset forged in an open die to a height = 25 mm. The strength coefficient is 650 MPa and strain- hardening exponent is 0.12. Qa =1.11 (Qa takes into account both friction and workpiece geometry). Calculate the force required for upsetting this part at room temperature. O 1786 kN O 1648 kN O 1247 kN O 1109 kN O none of them
A plate that is 260 mm wide and 27 mm thick is to be reduced in a single pass in a two‑high rolling mill to a thickness of 22 mm. The roll has a radius = 510 mm, and its speed = 25 m/min. The work material has a strength coefficient = 235 MPa and a strain hardening exponent = 0.21. Determine (a) roll force, (b) roll torque, and (c) power required to accomplish this operation
Estimate the roll force, F, and the torque for an AISI 1020 carbon-steel strip that is 200 mmwide, 10 mm thick, and rolled to a thickness of 7 mm. The roll radius is 200 mm, and itrotates at 200 rpm. Note that K = 530 MPa and n = 0.26.
A 300 mm thick slab is being cold rolled using roll of 600 mm diameter. If the coefficient of friction is 0.08, the maximum possible reduction is,
Bar stock of initial diameter = 90 mm is drawn with a draft = 15 mm. The draw die has an entrance angle = 18°, and the coefficient of friction at the work‑die interface = 0.08. The metal behaves as a perfectly plastic material with yield stress = 105 MPa. Determine (a) area reduction, (b) draw stress, (c) draw force required for the operation, and (d) power to perform the operation if exit velocity = 1.0 m/min
A cylindrical ingot with D0 = 50 mm and h0 = 40 mm is cold forged using an open die.The final height is 20 mm. The coefficient of form / friction between the die and the workpiece isconsider Kf = 1.10.The material from which the ingot is made has the following characteristics:K = 600 MPa and η = 0.12.Determine the force (F) on the operation:a) Force required at the moment of reaching the yield point (ℇ = 0.002)b) Force required when you have a height of h = 30 mmc) Force required when there is a final height of h = 20 mmd) Construct the graphs: Force vs Δh and effort vs Δh
A strip (300x30 mm) is fed through a rolling mill with two powered rolls (each with radius of 300 mm) rotating at the speed of 60 rpm. The flow stress of work material is 90 MPa, and the coefficient of friction between rolls and work is 0.12. For a single rolling operation performed at the contact angle of 6.28°, calculate the followings:a) Work thickness after rolling (in mm)
A sheet 300mm wide 25mm thick with two drives, each with a radius of 250mmit is passed through a rolling stand with rollers. Work is thickness in one layer at 50 rpm roll speed 22reduced to mm. The work material has a yield curve determined by K = 275 MPa and n = 0.15.The friction coefficient between the rollers and the work is considered to be 0.12. Successful rolling of frictionDetermine if it is sufficient to allow its operation. If it is sufficient;a) Rolling force,b) Momentc) Calculate the power.
1. The friction in direct extrusion is ________ Indirect extrusion. a) Greater than. b) Equal to. c) Less than.2. The Temperature in hot forming process is ____. a) (0 to 0.4) Tm. b) (0.5 to 0.75) Tm. c) 0.9 Tm. d) 0.4 Tm. e) 0.8 Tm. f) (0.3 to 0.5) Tm. Where Tm is the melting temperature of the work piece.3. Maximum draft in rolling depends on _______. a) Coefficient of friction and roll radius. b) Thickness of plate. c) Smoothness of roll Surface. d) Roll rotational speed.e) Width of the plate. f) Length of the plate.4. In deep drawing process, the drawing ratio (DR) has a higher limit (value) of:- a) 6. b) 1. c) 4. d) 5. e) 7. f) 2. g) Zero.5. Spring Back is a phenomena usually associated with which of the following processes:-a) Extrusion. b) Forging. c) Bending. d) Wire drawing. e) Rolling. f) Sheet metal cutting. g) Deep Drawing.
A solid cylindrical slug made of 304 stainless steel is 150 mm in diameter and 100 mm high. It is reduced in height by 50% at room temperature by opendie forging with flat dies. Assuming that the coefficient of friction is 0.2 and the flow stress of this material is 1000 MPa, calculate the forging force at the end of the stroke. Manufacturing processes
A wire is drawn through a draw die with an entry angle = 15o. The starting diameter is 0.100 in. And the final diameter = 0.080 in. The coefficient of friction at the work-given interface = 0.07. The metal has a coefficient of resistance K = 30,000 psi and a strain hardening exponent of n = 0.20. Determine the stretching force and the stretching force in this operation.