Answered: A solid shaft of 150 mm diameter is…

A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: The solid compound shaft, made of three different materials, carries the two Torques shown. (a)…

Q: A motor driving a soiid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of…

A: Given data as per question Power transmitted =40KW Speed =500 rpm Diameter of We know that Power…

Q: If the power transmitted by the shaft is 400 kW at a speed of 2000 rev/min calculate: (i) (ii) The…

A: angular velocity of shaft in RPM = 2000 in rad/sec = 209.43951 rad/s

Q: Compare the weights of equal lengths of hollow shaft and solid shaft to transmit a given torque for…

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A: Given data:

Q: The outer diameter of the shaft is 100 mm and the diameter ratio is 1.25. Find the polar modulus of…

A: Outer diameter/ Inner diameter = 1.25.

Q: Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m2

A: Substitute the given values in the Maximum shear stress equation to get the diameter of the shaft.

Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm.…

Q: The shear stress–strain diagram for a solid 50-mm diameter shaft can be approximated as shown in the…

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

Q: For the steel shaft shown in Fig. Determine the torque transmitted by transverse cross sections at…

Q: Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1…

Q: A solid steel shaft is stressed at 100 Mpa when twisted through 6 degrees. Compute the Diameter of…

A: Given:ζ=100 MPaθ=6°f=25 HzL=15 mG=83 GPa

Q: Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed…

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: A 50 mm diameter shaft is transmitting a power of 142.8 HP and is turning at 900 rpm. The shaft is…

A: given data ; diameter = 50 mmpower = 142.8 HP = 142.8 * 746 Wrpm = 900 rpmbending stress =…

Q: A shaft is made of a steel alloy having an allowable shear stress of 10 ksi and the diameter of the…

A: Data givem - Shaft is made of steel alloy Allowable shear stress τallow = 10 ksi d = 1.2 inch…

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

Q: Find out the outer diameter of the hollow shaft, if the allowable shear stress induced in it is…

A: Data given- Allowable shear stress = 53 MPa Permissible value of torque = 2000 N-m K = di /do =…

Q: ropeller shaft of diameter 30mm. If the llowable shear stress of the shaft and oupling material is…

Q: A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear…

Q: Finding the value of sectional modulus of shaft having diameter 3 m

A: Given data : Diameter of shaft is given in this question . With help of this data we have to find…

Q: A solid steel shaft 3/4 inch in diameter and 5 feet long, is twisted through an angle of 6 degrees.…

A: Given- Diameter of shaft (d)= 0.75 in Length (L) = 5 ft = 60 inch Angle of twist θ θ=6 degrees =…

Q: Two shafts, one of steel and the other of phosphor bronze, are of the same length and are subjected…

A: Answer: (a) The diameter of the phosphor-bronze shaft is 28.12 mm. (b) The ratio of the maximum…

Q: The inner diameter of the shaft is 180 mm and the diameter ratio is 1.2. Find the polar modulus of…

Q: 5. The shaft of a motor has a length of 15 times its diameter and has a maximum twist of 1.5 degrees…

Q: If allowable shear stress in the shaft is 80N/mm? and the torque equivalent(Te) is 1.23 x106 N-mm.…

Q: The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure…

Q: A solid shaft has 100 mm diameter. It is used to transmits 120 watt power at 200 rpm (Take G = 8 x…

A: Given:Power transmited P=120π Wmodulus of rigidity G=8×104 N/mm2Diameter of shaft d=100 mm or 0.1…

Q: The outer diameter of the shaft is 175 mm and the diameter ratio is 1.25. Find the polar modulus of…

Q: The tubular drive shaft for the propeller of a hovercraft is 6 m long. If the motor delivers 4 MW of…

A: Given data as per the question Length of shaft =6 m Power delivered =4 MW The outer diameter of the…

Q: A SOLID circular shaft transmits 50 horsepower while operating at a rate of 150 rev/min. If the…

Q: solid steel shaft must not twist through more than 3° in a 6-m length when subjected to a torque of…

Q: Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear…

A: GIVEN DATA- MAXIMUM SHEAR STRESS = 70MPa POWER P=90KW SPEED N=180 r.p.m. MAXIMUM TORQUE = 140% OF…

Q: The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure…

Q: Problem 1

A: Due to the torques at point B, C, D, E, and G, there exists a reaction torque at point A.Sign…

Q: A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of…

Q: A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A: given data :- diameter of shaft = 0.64 in find the shear stress in shaft (3).

Q: 3.12 The solid compound shaft, made of three different materials, carries the two torques shown. (a)…

Q: Determine the torque that can be transmitted by this shaft. D = 120 mm Outer diameter, Inside…

Q: The solid and hollow shafts are each subjected to the torque T. In each case, sketch the shear…

A: The solid shaft is subjected to torque T in a clockwise direction. The shear stress is calculated…

Q: applied, find this torque, the maximum shear stress, and the angle of twist per unit length. G = 85…

A: for solution refer below images. NOTE:- generally value of modulus of rigidity (G) is in Gpa, but in…

Q: A solid shaft 100 mm diameter transmitted power at 150 rpm. If the maximum shear stress induced in…

Q: 2. If 75 N/mm is the maximum shear stress and 50 kN-m is the torque acting on a solid shaft, then…

A: Given: Maximum shear stress τmax = 75 N/mm2 = 75000 kN/m2 Torque acting on a shaft T = 50kN-m…

Q: A hollow steel propeller shaft, 18 ft long with 14-in. outer diameter and 10-in. inner diameter,…

Question

A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
A hollow circular shaft has an outer diameter of 100 mm and a wall thickness of 25 mm. The allowable shear stress in the shaft is 125 MPa. Find the maximum torque that the shaft can transmit.
find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft transmits 150 KW power at 150 RPM.
A shaft is used to transmit 24 kw at a speed of 1,779 rev/min. Using a maximum allowable shear stress of 48 MPa, find the shaft diameter in mm
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.