A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of the shaft if the angle of twist is limited to 5° in a length of 3 meters and the shear stress is not to exceed 47 MPa. Use G = 83 x 10° Pa.

A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of the shaft if the angle of twist is limited to 5° in a length of 3 meters and the shear stress is not to exceed 47 MPa. Use G = 83 x 10° Pa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: What is the weight of a 1-lbm mass at an altitude where the local acceleration of gravityis 32.0 ft/...

A: The universal law of gravitational states that there is a force of attraction between any two partic...

Q: Two plates are held together by 4, 28 mm diameter bolts. If a 25 kN load is applied to the plates in...

Q: he correct stress state for representing the circumference of the pressure vessel is which of the pl...

A: Stress developed in cylindrical pressure vessel is longitudinal stress and hoop stress.

Q: The air in an automobile tire with a volume of 2.60 ft^3 is at 90 degF and 20 psig. Determine the am...

Q: what is the law or theory will be used to find the car speed model? what is the law or theory will b...

A: given; what is the law and theory will be used to find the car speed model. what is the law and the...

Q: 1. In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. The weig...

Q: Determine the pressure difference between the inside and outside of the 0.13 mm diameter air bublle ...

Q: B. If the force vector shown below has x, y, and z components of 300 N, 400N, and 800N respectively,...

Q: Five kilo of water vapour are contained at 178 kPa and 85 percent quality is a suitable enclosure. C...

Q: For part d, we introduce a wall at cross-section A. Determine the absolute maximum shear stress on t...

Q: A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractor if it is operat...

Q: 2. How to find what a materials crystal structure is? (FCC, BCC or neither FCC or BCC or others) 3....

Q: Determine the number of the impellers required for a multi stage pump to lift 4200 litres/minute aga...

A: We have, Total head, H=185 m, N=750 rpm, Ns=70 rpm Q=4200 litres/min=4200×10-360=0.07 m3/s

Q: Show how you would find the velocity of each point (no values given just the equation) for an overla...

Q: Crate A is traveling down the incline with a speed of 3.6 m/s when in the position shown. It later s...

Q: If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) in meter...

Q: oble with a diameter of 2.72" is to be enlarged by blowing air into it. If the surface tension of th...

A: D1= 2.72" D2= 3.64" (Surface Tension) T= 0.0035 lbf/ft To find :- Work input required.

Q: Using PSYCHROMETRIC CHART, find the unknown properties of the following conditions below: Pair=97.6...

A: Pair=97.6kPa, P=100 kPa and tdry = 35oC

Q: Imagine that a fluid velocity field can be found with the same motion rotation of a CD inside a CD ...

A: Voticity is described as local spinning motion of a fluid as seen by an observer located at a point ...

Q: In the figure shown: Pk is the same for point A and B. What is the acceleration(m/s²) of the block i...

Q: PROBLEM 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Worki...

A: Dear students The answer is given below---

Q: The attached answer was provided for the attached question. The equation uses the given temperature ...

A: given; The attached answer was provided for the attached question. The equation uses the given tempe...

Q: The rectangular plate is deformed into the shape shown by the dashed lines. If ?? has a normal strai...

Q: An orificemeter with orifice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure di...

Q: A centrifugal pump delivers 1.27 m' of water per 1200 r.p.m. The impeller diameter is 350 mm and bre...

Q: olve questions (2, 3 and 5)

A: Given Engineer's in situation To find Moral Dilemma Applicable values Action to be taken

Q: B. 30°

A: Givenweight of the cylinder W=30+51=81Nθ=30oFCB=2FCA

Q: The following instruments are considered gyroscopic. * Tachometer VSI Altimeter Fuel qua...

Q: 1. Loads are applied on a pipe made up of steel, bronze and aluminum. The forces and areas are shown...

A: Given:P=3000 lbA=0.5 in2

Q: Blocks A, B, and C weigh 300, 150, and 50 N respectively. Neglecting Friction, the stiffness of the ...

Q: Determine the resultant moment about point A of the system of forces. Note that Each square is 1 ft ...

Q: A centrifugal pump running at 1200 r.p.m. delivers water. The diameter of the impeller at the inlet ...

A: By referring the given diagram we have, N=1200 r.p.m ; D1=100 mm=0.1 m,D2=300 mm=0.3 m,B1=50 mm=0.5 ...

Q: total drill time in seconds is

A: Given data; In a single pass drilling operation,Hole oil diameter,d=15 mmDrilled in a steel plate ha...

Q: 1- Define the surface tension? What is depending on? 2- What is the relation between the liquid type...

A: Surface tension is a phenomenon exhibited by liquid surfaces at rest. It depends on the type of liqu...

Q: What is his weig

Q: Find the velocity, acceleration, and speed of a particle with the given position function. r(t) = 2i...

A: As given in question, Position function = r(t) = t2 i + 8t j + 3 ln(t) k From position function, v...

Q: The maximum thermal efficiency possible for a power cycle operating between 1096°F and 267°F is ____...

A: Given data, T2= 267°F T1=1096°F

Q: A 4 stroke gas engine develops 4.5kw at 180rpm at full load.Assuming the following data, calculate t...

Q: Q2/ Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced...

Q: The shop test of a single-acting, 8" x 12" engine whose record is hereby reported was made for the h...

Q: 2. Find the magnitude of the force F2 and the angle if the acting on

A: Need to find Magnitude of force and angle

Q: Determine the smallest safe diameter of the solid steel shaft if the maximum shear stress is 50,000 ...

Q: A shaft stepping from 2" to 3" has a fillet radius of 0.25". Compute the maximum bending stress, in ...

Q: 1. In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. The weig...

Q: fluid is flowing in a glass pipe at a rate of 0.587 kg/s. The pipe has a diameter of 67.5 mm. If the...

Q: P3.108 A rocket sled of mass M is to be decelerated by a scoop, as in Fig. P3.108, which has width b...

Q: A pot contains water and is heated on a cooker. The cooker adds 23.3 kJ to the pot with 0.8 kJ lost ...

Q: Assumptions: 1. The water is a closed system 2. The initial and final states are at equilibrium. The...

Q: P is known to have a value equal to 250 Ibs. Using rectangular components, determine (a) the value o...

Q: 3.23 Consider the geared system in Figure P3.23, where double-headed arrows are used to describe tor...

A: Given : To find : Free body diagram Equations Transfer function

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

c, Use 2 decimal place for the final answers.

Problem 3..
A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of the
shaft if the angle of twist is limited to 5° in a length of 3 meters and the shear stress is not to exceed 47
MPa. Use G = 83 x 10° Pa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Problem: 2 A solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum torque transmitted exceeds the mean torque by 20%. Take the maximum allowable shear stress as 78 MPa.
Q2: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be transmitted for a limiting shearing stress of 60 MN/m2 in the steel. It is proposed to replace A by a hollow shaft B, of the Same external diameter but with a limiting shearing stress of 75 MN/m2 . Determine the internal diameter of B to transmit the same power at the same speed.
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft is 3 m and modulus of rigidity is 83,000 MPa. Which of the following gives the torque carried by the shaft?a. 1.59 kN-m c. 2.69 kN-mb. 3.45 kN-m d. 4.81 kN-m Which of the following gives the minimum diameter so that the allowable torsional shearing of 40 MPa will not beexceeded?a. 88 mm c. 59 mmb. 45 mm d. 76 mm Which of the following gives the minimum diameter so that the allowable angle of twist of 6O will not be exceeded?a. 29 mm c. 35 mmb. 49 mm d. 55 mm
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.