A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a. What is the torsional rigidity of the post if the shear modulus of elasticity is 80 GPa? b. Determine the torsional stiffness of the steel post. Determine the maximum shear stress in the steel post if it is subjected to a torque of 612 N-m.

A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a. What is the torsional rigidity of the post if the shear modulus of elasticity is 80 GPa? b. Determine the torsional stiffness of the steel post. Determine the maximum shear stress in the steel post if it is subjected to a torque of 612 N-m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3650 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft.
A circular steel rod of diameter d is subjected to a tensile force P = 3.5kN The allowable stress in tension and shear are 190.6 MPa and 70.3MPa, respectively. What is the minimum permissible diameter dmin of the rod (in mm)?
A solid 1.500-in.-diameter steel [G = 12,000 ksi] shaft is subjected to torques TB = 270 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 54 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque TC that can be applied to the shaft.
The steel shaft of a socket wrench has a diameter of 8.0 mm. and a length of 200mm (see figure). If the allowable stress in shear is 60 MPa, what is the maximum permissible torque Tmax that may be exerted with the wrench? Through what angle f (in degrees) will the shaft twist under the action of the maximum torque? (Assume G=78 GPa and disregard any bending of the shaft.)
Given a rectangular hollow box with outer dimensions 125mm x 85mm and constant thickness of 10mm has an ultimate stress of 415 MPa. Modulus of Elasticity of 110 GPa. a. Determine the bending moment M for which the factor of safety will be 2.50. b. Determine the corresponding radius of curvature of the section.
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. a. What is the moment of inertia (in mm4) of the cross-section of the beam? b. What is the value of Q (in mm3)? c. What is the actual bending stress of the beam in MPa? d. What is the actual shearing stress of the beam in MPa?
A cantilever of circular solid cross section is fixed at one end and carries a concentrated load P at the free end. The diameter at the free end is 200mm and increases uniformly to 400mm at the fixed end over a length of 2 m. At what distance from the free end will the bending stress in the cantilever be maximum? Proceed to calculate the value of maximum bending stress if the concentrated load P = 30 kN. I need answer ASAP. Thank you!
The shaft is made of two segments. AC has a diameter of 0.5in, and CB has a diameter of 1in. It is fixed at its ends A and B and is subjected to a torque T=500lb*ft. Gsteel= 10.8*103 ksi What is the minimum shear stress in the shaft?
PLEASE ANSWER ASAP TY! a) What is the magnitude of internal torque in segment CD (in N-m)? b) What is the magnitude of internal torque in segment AC (in N-m)? c) What is the magnitude of torsional shear stress in segment DB (in MPa)? d) Determine the maximum torsional shear stress in the shaft (in MPa). e) What is the angle of twist of the shaft at B relative to A (in degrees)?
The frame shown below is fixed at point Q and subjected to the axial load at free end in both points A and B, if (a) (Es/Ec) = 8, (b) direction x and y axis. Determine the actual stresses acting (Es/Ec) = 0
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
4. A torque of 9.5 kN is to be carried by a flanged bolt coupling that consists of eight 12 mm diameter steel bolts on a circle of diameter 300 mm and six 12 mm diameter steel bolts on a circle of 250 mm. Determine the shearing stress in the bolts.