A square frame 3m by 3m in dimension is submerged in water vertically with its top 3m from the surface. If oil, (s.g=0.80) occupies the top meter, determine the pressure at the bottom of the frame. A) 58.78kPa B 57.78kPa 56.78kPa 59.78kPa

A square frame 3m by 3m in dimension is submerged in water vertically with its top 3m from the surface. If oil, (s.g=0.80) occupies the top meter, determine the pressure at the bottom of the frame. A) 58.78kPa B 57.78kPa 56.78kPa 59.78kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 737 grams of dry sand completely fills a 500 cm³ permeameter tube. The specific gravity of the sand…

A: Given data : The value of density of water ρw=1 g/cm3 The value of volume of permeameter tube V=500…

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN…

Q: 2..Calculate the moment at the supports using 3-moment equation and draw the shear and moment…

Q: (per metre leng t head of 10 m. D-6 m/sec

Q: A sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 36.6°. The…

Q: Failure of Rigid pavements, their cause and repair

Q: what is TH, in °F? "C, what is TL, in °C?

A: Reversible process: - It is defined as the process in which system and surrounding can reach from…

Q: This is the product of the arrival rate and average waiting time in the queue. a. Average waiting…

Q: A triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure…

Q: 4m 500 N 400 N B 3m3m 3m- -3m

Q: Vehicle time headways and spacings were measured at a point along a highway, from a single-lane…

A: Given:- The average values of the vehicle time headways = 2.5 sec/veh The spacing = 200 ft/veh To…

Q: According to Contract Act (1950), there are seven (7) essential elements to the creation of a valid…

Q: A rod of length 2 m and diameter 50 mm is elongated by 5 mm when an axial force of 400 KN is…

A: given- rod length L=2 mdiameter d=50 mmelongation ∆L=5 mmaxial force P=400 kN

Q: For the given structures, determine the degree of indeterminacy. 8.

A: External indeterminacy = re - 3 = 6 -3 = 3 Internal indeterminacy = 3C - rr…

Q: 2. Calculate the value of y at the free-end, slope at the supports. Use E = 200 GPa, I = 150 x 10…

Q: 4. A simply supported beam of length L = 10 m with a concentrated force F = 30 kN applied at the…

Q: 100 lb/in. A -30 in.- 40 lb/in. B 1.8 in. O

Q: The y-component of the force F which a person exerts on the handle of the box wrench is known to be…

A: FBD : Given data : The value of component of force F in Y direction FY=66 lb The value of angle…

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a…

A: This question is related to the Strength of Material.

Q: 3. Assuming a circle watershed with radius 900km has its center at the origin. The rain gauges are…

Q: MB ← a —x а B C За x а –ха |Ę₂₁₂ F

Q: 2..Calculate the moment at the supports using 3-moment equation and moment diagrams. 15 kN/m 20 kN/m…

Q: Q2: What are the assumptions for using the equations in the queue test?

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: 450 N 30⁰ B 30° MATHalino.com C 450 N MATHalino.com 30°

Q: A |1200 lb 180 lb/f 12 ft B 4 in. 18 in

Q: A lake had a water surface elevation of 103.200 m above datum at the beginning of a certain month.…

Q: What is the "confinement zone" in relation to special lateral tie spacing for columns for seismic…

A: The Zone or we can say structural joint (mainly) where there is a possibility of occurring of…

Q: Beam ABCD carries a concentrated load and uniformly distributed load as shown below. Find the shear…

Q: Book the readings as shown in Figure Q5 by Rise and Fall method. Compute all elevations, and show…

A: Station BS IS FS Rise Fall RL BM 61 4.72 321.70 0+00 4.42 0.3 322.00 0+50…

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: -0.61 m B 356 N 0.61 m H 356 N 0.61 m G F 0.46 m 267 N 178 N 0.61 m

Q: The beam is subjected to a 50 kN-m factored torque at critical section near the face of support. The…

Q: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the shear force 6.81…

Q: (Q2) Determine the maximum normal stress due to bending of the beam loading shown below. 5 kN 20…

Q: 2. Calculate the value of y at the free-end, slope at the supports. Use E = 200 GPa, I = 150 x 10…

Q: 100 KN 60 kN 3m J G 4m 3m 40KN D 3m A Second Level: 100 KN 1.5m H B First Level: 100 KN 3m 60KN 1.5m…

Q: Consider the structure below, the components of the reaction force at C are Cx = ___N. 500 N 400 N…

A: The structure has 4 reactions, with three equations of equilibrium and one compatibility equation…

Q: 4m -3m B 500 N 400 N 3m 3m 3m

Q: The cage system in the figure is carrying the load shown. a) Determine the forces in the bars HI, HB…

A: Please find step by step answer below:

Q: A bungee jumper who weighs 200lb jumps from a bridge 130ft above a river. The bun gee cord has an…

A: given:Weight of bungee jumper, W=200 lbCord unstretched length, L=60 ftspring constant, k=14 lb/ft

Q: A reversible power cycle receives energy QH by heat transfer from a hot reservoir at TH and rejects…

A: Given Data :

Q: A 6 kN RA 4 KN 1 kN/m A D CV A 1 kN/m + 1m 2m 2m 1m Note: The uniformly distributed load is extended…

Q: A column is constructed using four A992 steel angles that are laced together as shown. The length of…

A: Given :

Q: The properties of the reinforced concrete beam are b = 300 mm, d = 480 mm, Ast = 1306 mm2, and Est /…

A: Given data: b=300 mmd=480 mmAst=1306 mm2m=10σc=16.7 MPaσs=104.8 MPa Assuming cover as 20 mm D=500 mm…

Q: An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress…

Q: B) Solve the following differential equation:- 3x² 2√x ]

A: For the given differential equation,

Q: 20 kN m 5 KN 4 kN/m 6 m انا 6 m 6 m

Q: Draw the shear-force and bending-moment diagrams for the beam shown. Determine the shear force 9.5…

Q: Calculate the density and specific weight of nitrogen

A: Solution: Given data, Absolute pressure = 1 Mpa = 106 pascal Temperature = 40 c = 40 + 273 = 313 K…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

A square frame 3m by 3m in dimension is submerged in water vertically with its top 3m from the surface. If oil, (s.g=0.80) occupies
the top meter, determine the pressure at the bottom of the frame.
A) 58.78kPa
B) 57.78kPa
56.78kPa
59.78kPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular plane surface 1 m wide and 3 m deep lies in water in such a way that its plane makes an angle of 30 degrees with the free surface of water. Determine the position of the center of pressure from the free water surface when the upper edge of the plate is 2 meter below the free water surface. a. 1.686 m b. 2.318 m c. 2.0 m d. 4.56 m With F.B.D
A triangular plate of 1 m base and 1.5 m altitude is immersed in water. The plane of the plate is inclined at 30° with water surface while the base is parallel to and at a depth of 2 m from the water surface. Calculate the total pressure on the plate in KN. a.13.56 b.21.45 c.16.54 d.19.34
A square tank 1.20m on each side, 3m deep is filled to a depth of 2.7m with water. A wooden cube having a specific gravity of 0.5 measuring 60cm on an edge is placed in the water so that it will float. Determine the depth of submergence of the cube in the water, the rise of water above the original liquid surface, and the distance of the bottom of the cube from the bottom of the tank.
A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the horizontal, the 1.2 m sides being the horizontal. a. what is the minimum lressure acting on the plane in kPa b. what is the maximum lressure acting on the plane kPa c. Determine the magnitude of hydrostatic force acting on either side of the plane in KN. Support your computations with correctly drawn and labrled pressure prism diagrams.
If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance below the liquid surface, determine the depth to its center of pressure. What is the horizontal force acting on the triangle? Assume ? water = 9790 N/m3. f = depth to apex, 2m d = height of triangle, 1m a = width of triangle, 1m The horizontal force (N) acting on the triangle is:
A square tank 1.20m on each side,3m deep is filled to a depth of 2.70m with water. A WOODEN CUBE having a specifix gravity of 0.5 measuring 60 cm on an edge is placed in the water so that it will float. A.) Determine the weight of the water displaced by the cube Choices: 2.12 kN,1.06kN,1.15kN,2.30kN B.)Determine the rise of water above the original liquid surface Choices: 0.15m,0.088m,0.075m,0.30m C.) Determine the change in pressure force on one side of the tank Choices: 2.84kN,2.55kN,2.42kN,2.75Kn
Determine the total pressure in kN on a plane rectangular surface of 1 m wide and 3 m deep when its upper edge is horizontal and coincides with water surface. a. 121.45 b. 103.0 c. 59.34 d. 44.14
Assume g=10 m/s2
A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140 KPa greater than at A. f= 0.019 Determine the head loss in meters. choices: 7.25, 5.27, 2.75, 7.52
Determine the vertical displacement of node A. Consider EA = 16x104 [kN-m]
Gate AB is 1.0 m long by 1.5 m wide. What is the position X of its center pressure in mm?