A stationary diesel engine with a thermal efficiency of 40% produces 200 horsepower. The exhaust gas, which we suppose is air, has a velocity of 1400 R, whereas the intake has a velocity of 520 R. What is the mass flow rate if it accounts for half of the QL?

A stationary diesel engine with a thermal efficiency of 40% produces 200 horsepower. The exhaust gas, which we suppose is air, has a velocity of 1400 R, whereas the intake has a velocity of 520 R. What is the mass flow rate if it accounts for half of the QL?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
In a reaction turbine, the drum diameter is 2.15 m, speed of turbine is 750 rev/min and the steam flow is 14.2 kg/sec. At a particular ring of blades, the blade height is 15.875 cm and the discharge angle (α & ϕ) is 25°. Here, the pressure of steam is 0.04 N/mm2 abs, and its dryness fraction is 0.97. Determine the following: 2. Heat drop, in kJ, through this turbine pair, assuming turbine efficiency of 80%
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A turboprop engine consists of a diffuser, compressor, combustor, turbine, and nozzle. The turbine drives a propeller as well as the compressor, delivering a net power of 1 MW to the propeller. Air enters the diffuser at 8000 m altitude (Ta = 236K, pa = 36 kPa) with a velocity of 550 km/h, and decelerates essentially to zero velocity. The compressor pressure ratio is 5.3 and the compressor has an isentropic efficiency of 83%. The turbine inlet temperature is 1360 K, and its isentropic efficiency is 86%. The turbine exit pressure is 10 kPa higher than the ambient pressure at that altitude. Flow through the diffuser and nozzle is isentropic. Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Using an air-standard analysis, determine: a) The mass and volumetric flow rates entering the diffuser, in kg/s and m3/s, respectively.b) The rate of heat addition to the combustor, in MW.c) The velocity at the nozzle exit, in m/s.
A single-stage impulse turbine of nozzle efficiency, 90%, nozzle angle=20, absolute velocity of steam entering moving blade-672.4m/s, the ratio of blade speed to whirl component of steam speed 0.5, blade velocity coefficient =0.9.the velocity of steam entering the nozzle =20mis. Determine the blade angles at inlet and outlet if the steam enters into the blades without shock and leaves the blades in an axial direction, 2- blade efficiency, and 3- power developed and axial thrust if the steamflow is 8kg/s (Solve using the velocity diagram).
In a reaction turbine, the drum diameter is 2.15 m, speed of turbine is 750 rev/min and the steam flow is 14.2 kg/sec. At a particular ring of blades, the blade height is 15.875 cm and the discharge angle (α & ϕ) is 25°. Here, the pressure of steam is 0.04 N/mm2 abs, and its dryness fraction is 0.97. Determine the following: 1. Power developed, in kW, by the particular ring. 2. Heat drop, in kJ, through this turbine pair, assuming turbine efficiency of 80%
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
A small ramjet engine is to be designed for a maximum thrust of 1000 lb at sea level at a velocity of 950 ft/s. If the exit velocity and pressure are 2000 ft/s and 1.0 atm, respectively, how large should the inlet be?
Steam at 200 psia and 600°F (state 1) enters a turbine through a standard 3-in pipeline with a velocity of 10 ft/s. The exhaust from the turbine is carried through a standard 10-in pipeline and is at 4 psia and 160°F(state 2). Data: H1=1321.4 BTU/lb, V1= 3.059 ft³/lb, H2=1129.3 BTU/lb, V2=92.15 ft³/lb. What is the power output of the turbine in W, assuming no heat losses.A. 29989.2B. 32152.6C. 34017.6D. 35435.0
Air at 7°C enters a turbojet engine at a rate of 16 kg/s and at a velocity of 220 m/s (relative to the engine). Air is heated in the combustion chamber at a rate 15,000 kJ/s, and it leaves the engine at 427°C. Determine the thrust produced by this turbojet engine. (Hint: Choose the entire engine as your control volume.)
In the first stage of the impulse turbine, the adiabatic heat drop in the nozzle is 350 (kJ/kg), the velocity coefficient of the nozzle is 0.96, the nozzle exit angle is 20 degrees, the circumferential speed of the rotor is 350 m/s, the rotor The exit angle is 30 degrees. Find the next value.(1) Nozzle efficiency, (2) Draw a velocity triangle (scale), (3) Circumferential force acting on the rotor blade (4) Find the forward efficiency of the turbine.