A steam power plant operates on a Rankine Cycle. Steam enters the turbine at 600° Cand 15 MPa and exits the turbine at 15 kPa. The turbine isentropic efficiency is 88%. The pump has an isentropic efficiency of 92%. The steam flowrate into the turbine is 200 kg/s. What is the turbine outlet temperature the turbine outlet quality entropy heat input a T-s diagram , the turbine outlet enthalpy the turbine outlet the rate of the turbine output power and the cycle thermodynamic efficiency the pump input power Show the process on

A steam power plant operates on a Rankine Cycle. Steam enters the turbine at 600° Cand 15 MPa and exits the turbine at 15 kPa. The turbine isentropic efficiency is 88%. The pump has an isentropic efficiency of 92%. The steam flowrate into the turbine is 200 kg/s. What is the turbine outlet temperature the turbine outlet quality entropy heat input a T-s diagram , the turbine outlet enthalpy the turbine outlet the rate of the turbine output power and the cycle thermodynamic efficiency the pump input power Show the process on

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam generated at a power plant at 8.0 MPa and 600.°C is fed to a turbine. Exhaust from the turbine enters a condenser at 25 kPa where it is condensed to a saturated liquid, which is then pumped to the boiler. What is the thermal efficiency of a Rankine cycle with a reversible adiabatic turbine operating at these conditions?
In a standard Rankine cycle steam enters the turbine at pressure p3=10mpa and temperature T3=350cThe exit pressure of the steam from the turbine is p4=10kpa A. What is the quality of the steam leaving the turbineB. What is the thermal efficiency of the cycle? C. Reduce the turbine inlet pressure to 3.5 MPa.In this situation, the steam quality at the exit of the turbine will be x = 0.801, and the thermal efficiency will be 34.1%State an advantage and a disadvantage of using a turbine inlet pressure of 10 MPa compared to a turbine inlet pressure of 3.5 MPa. Refer to the quality of the steam leaving the turbine and the efficiency of the cycle.
Air enters the compressor of a regenerative gas-turbine engine at 100 kPaand 300 K and is compressed to 800 kPa. The regenerator has aneffectiveness of 65 percent, and the air enters the turbine at 1200 K. For acompressor efficiency of 75 percent and a turbine efficiency of 86 percent,determine(a) The heat transfer in the regenerator.(b) The back work ratio.(c) The cycle thermal efficiency
Hi! im having issues with this problem, thanks or the help! a 210 MW steam power plant operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500o C and is cooled in the condenser to a pressure of 20 kPa. Show the cycle on a T-s diagram with respect to the saturation lines and determine (a) the quality of steam at the turbine exit, (b) the thermal efficiency of the cycle, and (c) the mass flow rate of the steam.
A simple power plant utilizing the Rankine Cycle operates with an inlet boiler pressureof 5 MPa and an inlet condenser pressure of 300 kPa. Because of frictional effects, thepressure of the water drops 0.3 MPa in the boiler and 3 kPa in the condenser. Thetemperature of the steam as it enters the turbine is 700 °C. The adiabatic efficiency ofthe pump and of the turbine are 83 percent and 88 percent, respectively. The pumpand the turbine are adiabatic, and the water enters the pump as saturated liquid. It canbe assumed that heat transfer to the water in the boiler is from a reservoir at 1500 K,and the environment is at 25 °C.Determine the thermal efficiency of the cycle and compare it with the thermal efficiencyof (a) a Carnot cycle, and (b) the ideal Rankine Cycle. Specify the amount of entropygenerated in each step of the real cycle
Consider a heat engine is operating on a steady‐flow Carnot cycle with water asthe working fluid. The water mass flow rate in cycle is 0.5 kg/s. The cyclemaximum per minimum absolute temperatures ratio is 2.5. The quality of wateris 1 at the beginning of the heat‐rejection process and 0 at the end and theambient temperature is 35°C. Show the cycle on a T‐s and P‐v diagrams relativeto the saturation lines, and determine (a) the thermal efficiency, (b) thepressure at the turbine inlet, (c) maximum temperature, minimum pressure (d)the network output, (e) the entropy changes in all processes, and (f) the actualnetwork output with second law efficiency of 45%.
A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa and 550.0 ∘C.The exhaust steam enters the condenser at 50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 2.900 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: the thermal efficiency of the cycle, ?th:
A basic Rankine steam power plant uses an adiabatic turbine that operates with inlet steam at 6.80 MPa and 550.0 ∘C. The exhaust steam enters the condenser at 50.0 ∘C with a quality of 0.960. Saturated liquid water leaves the isobaric condenser and is pumped to the boiler. Mass flow through the cycle is 2.900 kg/s. Neglecting pump work and kinetic and potential energy changes, determine: the work interaction term of the turbine: the thermal efficiency of the cycle, ?th: the second law efficiency of the turbine, ?2nd:
In a simple Rankine cycle, the working fluid is water, operating at pressures between 7.5 kPa and 1750 kPa. The water vapor is in the form of saturated steam at the turbine inlet. Turbine expansion andCalculate the thermal efficiency of the cycle, assuming that the compression processes in the pump are reversible adiabatic.
The turbine of a steam power plant operating on a simple ideal Rankine cycle produces 500 kW of power when the boiler is operated at 3.5 MPa, the condenser at 40 kPa, and the temperature at the turbine entrance is 650oC. Determine: (a)the rate of heat supply in the boiler, (b)the rate of heat rejection in the condenser, and (c)the thermal efficiency of the cycle. Answers: (a) 1458 kW, (b) 958 kW, (c) 0.343
Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of 20MW. Steam enters the turbine at 7MPa and 450.210C and is cooled in the condenser at a pressure of 10kPa by running cooling water from a lake through the tubes of the condenser at a rate of 1750kg/s. Determine the value of enthalpy of steam at the entry to the steam turbine (accurate to 4 decimal places, using the relevant equations) assuming that the cp of superheated steam is 2.9699kJ/kg.K.
A Carnot cycle is executed in a closed system anduses 0.0025 kg of air as the working fluid. The cycle efficiencyis 60 percent, and the lowest temperature in the cycle is300 K. The pressure at the beginning of the isentropic expansionis 700 kPa, and at the end of the isentropic compressionit is 1 MPa. Determine the net work output per cycle.