A steam powerplant operates on the Rankine cycle. Determine the steam rate, the heat transferrates in the boiler and condenser, and the thermal efficiency of the plant Given Data: P2 = P3 = 9000 kPa; T3 = 650 degree Celsius; P4 = P1 = 20 kPa; Efficiency (turbine) = 0.85; Efficiency (pump) = 0.80; Power rating = 50000 kw please use perrys chem eng handbook when answering

A steam powerplant operates on the Rankine cycle. Determine the steam rate, the heat transferrates in the boiler and condenser, and the thermal efficiency of the plant Given Data: P2 = P3 = 9000 kPa; T3 = 650 degree Celsius; P4 = P1 = 20 kPa; Efficiency (turbine) = 0.85; Efficiency (pump) = 0.80; Power rating = 50000 kw please use perrys chem eng handbook when answering

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 15RQ: Why is two-stage compression popular for extra-low-temperature refrigeration systems?

See similar textbooks

Similar questions

A Steam Power Plant operates on the Rankine Cycle in which steam at 22 bar and dryness fraction of 0.95 enters the turbine and exhausts to a pressure of 0.1 bar in acondenser. The condensate is pumped as feedwater to the Boiler in which the steam is generated. Sketch the T-s diagram for this cycle and calculate the following performance parameters:(i) Cycle Thermal Efficiency(ii) Specific Steam Consumption(iii) Condenser Heat Load(iv) Cooling Water mass and volumetric flow rates for the condenser if the cooling water enters at 26 oC and leaves at 40 oC for a net power output of 24,000 kW. The specific heat capacity of the cooling water can be taken as 4.0 kJ/kg K and its density as 1023 kg/m3.
Q2/ Actual Rankine cycle, has the following specifications: Boiler pressure is 160 bar and Turbine inlet temperature is 600 Co and Condenser pressure is 0.08 bar , Turbine efficiency is 0.9 and Pump efficiency is 0.85 and Steam mass flow rate is 130 kg/s Calculate: 1-Work net (kW). 2-heat addition (kW) 3-thermal efficiency.
A superheat steam Rankine cycle has turbine inlet conditions of 10 Mpa and 500 C expands in a turbine to 0.010 Mpa. The turbine and pump polytropic efficiencies are 0.9 and 0.7 respectively pressure losses between pump and turbine inlet are 1.5 Mpa . Determine the following: A.)quality after turbine expansion B.) Turbine work C.)heat added in the boiler D.)heat rejected from the condenser E.)pump work F.) Net work G.)Cycle efficiency
Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: d) The work generated by the turbine; e) The condenser heat rejection rate (Q H); f) The coefficient of performance of the cycle.
The engine on a steam ship runs on the Rankine cycle. The steam leaves the boiler at 20 bar and 350°C. The turbine has an efficiency of 75% and an outlet pressure of 1 bar. The pressure changes in the boiler and condenser can be considered negligible, and the liquid leaving the condenser is saturated. A. Determine the operating temperature of the condenser, and compute the efficiency of a Carnot cycle operating between the boiler and condenser temperatures. B. Determine the actual efficiency of this Rankine cycle and compare it to the Carnot efficiency. C. When the Titanic was sinking, the Carpathia received the S.O.S. and immediately set course to attempt a rescue. The captain of the Carpathia ordered the hot water turned off in the passengers’ cabins (Lord, 1955). What effect do you expect this action had?
Steam enters the turbine of a power plant operating on the Rankine cycle (Fig. 2) at 873.15 Kand exhausts at 30 kPa. To show the effect of boiler pressure on the performance of the cycle,calculate the thermal efficiency of the cycle and the quality of the exhaust steam from theturbine for boiler pressures of 5000,7500, and 10 000 kPa. #Chemical Engineering #Chemical #Thermodynamics
Provide an expert insight about the methods used to increase thermal efficiency of a steam power plant.
An ideal Rankine cycle operates between the pressure limits of 15,000 kPa in the boiler and 15 kPa in the condenser. If the turbine inlet temperature is 500 deg C and the cycle produces 2500 kW of net work, determine the mass flow rate of the steam in kg/s. Refer to the tables below. a. 1.993 b. 2.122 c. 1.856 d. 2.016
A steam power plant working on Rankine cycle has the range of operation from 40 bar dry saturated to 1.2 bar. Draw the T-s and h-s diagrams and determine the following: (i) Steam quality at turbine exit (ii) Cycle efficiency (iii) Work ratio (iv) Steam rate
The mass flow rate of steam is 5 kg/s for a Rankine Cycle. For the actual cycle, the turbine efficiency is 86%, turbine brake efficiency is 80%, and generator efficiency=90%. The inlet conditions of the turbine are 3MPa and 400⁰C while the condensing pressure is 50kPa. a. Sketch the P-v, T-s and h-s diagram of the Cycle b. Calculate for the ideal and actual steam rates and heat rates of the Rankine Cycle and Rankine Engine, respectively. c. Determine the energy chargeable and combine thermal efficiencies for the Rankine Cycle and Rankine engine, respectively
You are an operating engineer in a steam power plant which is working on a regenerative Rankine cycle and you are requested to find the thermal efficiency of this cycle. You read the following data from the measuring devices used in the power plant: The pressure and temperature of the steam at the inlet of the turbine are 7000kPa and 550 °C, respectively. The pressure at the inlet of the condenser is 22 kPa. The extracted steam from the turbine is at 500 kPa and it is used to heat the feed water in an open feed water heater. The pumps and turbine efficiencies are 80% and 85%, respectively. Don't forget to show the evele on a T-s diagram.
An Actual Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. Steam leaves the boiler at 500°C. The cycle produces a Net Power of 10MW. a.) Determine the steam rate of the turbine. (kg/kW-hr) b.) Determine the steam rate of the turbine. (kg/kW-hr) c.) Determine the heat rate of the cycle (kJ/kW-hr) ROUND OFF ANSWER TO SIX SIGNIFICANT FIGURES