A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the turbine. The turbine has 200kW power output and heat abstracted of 100kW. If the mass flow rate is 1kg/s and the exit temperature of steam is 300C, find the exit turbine pressure

A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the turbine. The turbine has 200kW power output and heat abstracted of 100kW. If the mass flow rate is 1kg/s and the exit temperature of steam is 300C, find the exit turbine pressure

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: roblem 4: In the pump of a steam power plant, saturated liquid at 75 kPa pressure is compressed to 3…

A: Given, Pressure at the pump inlet, P1 = 75 KPa Pressure at the pump outlet , P2 = 3MPa = 300 KPa.…

Q: A two-stage compressor receives 0.35 kg/s of air at 100 kPa and 269K and delivers it at 5000 kPa.…

Q: pumped from 80 kPa to 3 MPa. The pump has an In a power plant, water (density = 1000 kg/m) is…

Q: 2.A steam throttling valve with inlet conditions of 2MPA and 400C is connected to the inlet of the…

Q: The compressor used in a refrigeration cycle takes in saturated R-134a vapor at a pressure of 360…

A: The entry pressure of the R-134a in the compressor, The exit pressure of the R-134a of compressor,…

Q: The enthalpy entering the turbine of a geothermal power plant is 2750 KJ/kg and ,ass rate of 1…

A: Enthapy at turbine inlet, h1= 2750 kJ/kg Mass flow rate in turbine, m˙= 1 kg/sec Turbine brake…

Q: A steam power plant has a turbine work of 320kJ/kg and the pump work is 2 kJ/kg. If the mass flow…

A: Given data, Wp= 2 kJ/kg Wt= 320 kJ/kg m= 10 kg/s

Q: Consider a steam turbine power plant as shown with the given properties below. Enter state of pump…

Q: Steam is supplied to a fully loaded 100-hp turbine at 200 psia with u1= 1163.3 Btu/lb, v1= 2.65…

Q: :In a gas turbine unit, the gases flow through the turbine and the power developed by the turbine is…

Q: Refrigerant-134a enters an adiabatic compressor at 15 psia and 20°F with a volume flow rate of 10…

A: The data given corresponds to the initial values of pressure, temperature, volume flow rate and…

Q: A boiler feed pump receives 40 L/s at 4 MPa and 180°C. It operates against a total head of 900 m…

A: Given data The discharge from the pump is Q=40 Ls=0.04 m3s The total head is H=900 m The efficiency…

Q: The heat pump with a power input of 2000 kW draws heat from a heat source at 70° C and gives heat to…

Q: Steam is delivered by a steam generating unit at 1100 psia and 900 F. After expansion in the turbine…

A: a) Given Data: P1=1100 psiT1=900 FP2=P3=300 psiT3=900 FP4= 1 psi

Q: ft3 min A two-stage compressor receives air at 100 at 10psia and the discharge pressure is 200 psia.…

Q: In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure…

Q: steam enters the system with enthalpy of 3300 KJ/kg at 200 m/s and leaves with enthalpy at 2700…

A: Given Data h1= 3300 kJ/kg h2=2700 kJ/kg V1=200 m/s V2=80 m/s

Q: Consider a steam turbine power plant as shown with the given properties below. Enter state of pump…

Q: The centrifugal compressor of a gas turbine receives air at 1bar and 300K. At the discharge of…

Q: b) A steam turbine that uses refrigerant 134-a as the working fluid is passed through a diffuser.…

Q: 2A steam throttling valve with iniet conditions of 2MPA and 400C is connected to the inlet of the…

Q: Que 4.35. A reaction turbine is revolving at a speed of 200 rpm and develops 5886 kW SP when working…

Q: Steam enters a turbine 80 lbs of steam per minute with an enthalpy of 1700 BTU/1lb and velocity of…

A: Given Data Mass of the steam, m=80 lb/min=1.34 lb/sec Inlet enthalpy, h1=1700 BTu/lb Outlet…

Q: The entropy of the steam increases in actual steam turbines as a result of irreversibilities. In an…

A: The entropy of a thing is a measure of the quantity of energy that cannot be used to do work.…

Q: A one-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and…

A: Solution: Given Data:

Q: An ideal turbine with one stage of reheat receives steam at 8 MPa, 500 degree C. Reheat pressure is…

Q: A reversible heat engine absorbs 3000 kJ from a reservoir at 1000 K and rejects 2500 kJ at 500 K.…

Q: The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It…

Q: A steam plant. the pressure levels are 10 kPa and 6000 kPa, and the steam leaves the turbine as…

Q: R134a is 400 kPa as saturated vapor to the compressor in a refrigerator system. enters at a pressure…

A: Solution :

Q: Two pounds per second steam enters the turbine at 500 ft/s with 600 btu/lb enthalpy and leaves at…

A: Write the given values with the suitable variables. m˙=2 pounds/sv1=500 ft/sh1=600 btu/lbv2=200…

Q: 600 kPa at 578 K and exits the turbine at a temperature of 428 K and a pressure of 100 kPa

A: apply first law of thermodynamics at inlet and outlet,here assume that air is an ideal gas.

Q: Find the exit temperature of the steam from the turbine. b. Find the output power of the turbine. c.…

A: Given: mass flow rate =2.5 kg/s T1= 600oC P1=6 Mpa P2=45 kPa turbine efficiency=91% To determine:…

Q: The heat pump with a power input of 2000 kW draws heat from a heat source at a temperature of 70 ° C…

Q: A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the…

Q: 2. In an aircraft refrigeration as shown in the figure below, air bled from the jet engine is at 326…

A: Simple air craft refrigeration system Neglecting ramming effect and considering inlet pressure to…

Q: A ¼ hp pump is used to pump water. The water enters the pump at 100 kPa and 15°C and exits the pump…

Q: eceives 6.85 m3/min of air at 96.53 kPaa, 43.3°C, and the high pressure cylinder (20.3 x 35.5-cm)…

Q: The heat pump with a power input of 2000 kW draws heat from a heat source at 70 ° C and gives heat…

A: Given that ;- Winput=2000 Kw Tsource=(70+273)° CTs=343 KAnd lets assume…

Q: A pump that is driven by a 7.5 hp motor takes water in at 720 degrees F and 5 psig and discharges it…

Q: Calculate the power in kilowatts of the gas turbine power plant has a greatest temperature of 700 C…

Q: Consider a steam turbine power plant as shown with the given properties below. Enter state of pump…

Q: Q1: The steam rate to a turbine for variable output is controlled by a throttle valve in the inlet…

A: Given Data Steam flow rate, m=0.6 Kg/s quality, x2=0.90 Exhaust steam, 10KPa Turbine power output,…

Q: A double-acting compressor with c= 7% draws 40 lb per minute of air at 14.7 psia and 80°F and…

A: Given:

Q: Kumargaon Power Plant operates, at the thermal efficiency equal to 88% of the Shahbazpur Power…

A: Given data:

Q: Que: The temperature in the evaporator of a home air conditioner using R134A as the refrigerant is…

Q: The heat pump with a power input of 2000 kw draws heat from a heat source at 70 ° C and gives heat…

Q: A two-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and…

Concept explainers

Forms of Energy

Energy is described as the capability to accomplish a task, like the ability to push a block by applying force on it. It is a quantitative property that is used to accomplish work on an object.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hi! Super needed rn, pleaase help me!! A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the turbine. The turbine has 200kW power output and heat abstracted of 100kW. If the mass flow rate is 1kg/s and the exit temperature of steam is 300C, find the exit turbine pressure.
Air enters a turbine at 900K and leaves at 300K. The turbine shaft is connected to a generator with an efficiency of 80%. If the mass flow rate of air through the turbine is 150kg/s, what is the electrical power produced by this turbine generator?
Water enters the cooling tower at 55°C and leaves at 30°C while the heat rejected to air is 120kW. Find the capacity of the pump needed to pump the water
A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that the outlet is at 45 °C, then reheats at 500 kPa up to 400 °C, then takes perform a low pressure expansion in the turbine. Determine: net power output
The heat pump with a power input of 2000 kW draws heat from a heat source at a temperature of 70 ° C and gives heat to a boiler. Saturated liquid water entering the boiler at 300 kPa pressure,It leaves the boiler as saturated steam at 300 kPa pressure performance of the heat pump=0.5 times the performance of the Carnot Heat pump Find the mass flow of water flowing from the boiler (kg/s)
Problem 4: In the pump of a steam power plant, saturated liquid at 75 kPa pressure is compressed to 3 MPa pressure. Since the adiabatic efficiency of the pump is 85%, find the work consumed by the pump.
The compressor used in a refrigeration cycle takes in saturated R-134a vapor at a pressure of 360 kPa and raises it to a pressure of 1.0 MPa. The compressor can be considered well-insulated and inlet and exit velocities are small. In steady-state operation, the mass flow is 0.048 kg/sec and the power requirement is 1450 Watts. Find the discharge temperature.
A one-stage compressor takes air at 100kpa and 25C with volume flow of 0.123m3/s and discharges to 800kpa. What is the heat rejected(kw) by the intercooler?
A steam turbine developed 2372.20 hp when its inlet condition is 1300 BTU/lb enthalpy and 400 ft/s velocity and steam flow of 200 lb/min. The exit enthalpy is 800 BTU/lb. Find the exit velocity. EXPLAIN STEP BY STEP
A two-stage compressor receives 0.35 kg/s of air at 100 kPa and 269K and delivers it at 5000 kPa. The setup is designed so that the temperature of the air entering the HP compressor is the same as the temperature of the air entering the LP compressor. If the compression follows the equation PV1.4=C, A.)Find the intermediate pressure B.)Find the heat transferred in the intercooler C.)Find the total work done D.)If motor output is 200 HP what is the compression efficiency?
The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It enters the turbine at a temperature of 1300 K and exits at a temperature of 800 K. Since the power of the gas turbine is 10 MW, b) Find the amount of fluid circulating in the installation. c) Find the adiabatic efficiencies of the gas turbine and the compressor. d) Find net work Note. Assume that the specific heat of heating of the air is constant. cp=1 kj/kgC cv=07181 kj/kgC
Water vapor enters an adiabatic turbine at a pressure of 8 MPa, a temperature of 600 ℃ and a speed of 100 m/s, and then a pressure of 50 kPa exits at a temperature of 150 ℃ and a speed of 160 m/s. The turbine power is 10 MW. According to this; a) The steam flow rate from the turbine b) Do you find the isanthropic efficiency of the turbine?