ft3 min A two-stage compressor receives air at 100 at 10psia and the discharge pressure is 200 psia. If the temperature of the air received is 50F, find the intercooler pressure, total compressor work and total heat rejected at the intercoolers. 44.72psia; 16.31 hp; 345.80 min Btu

ft3 min A two-stage compressor receives air at 100 at 10psia and the discharge pressure is 200 psia. If the temperature of the air received is 50F, find the intercooler pressure, total compressor work and total heat rejected at the intercoolers. 44.72psia; 16.31 hp; 345.80 min Btu

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: VB Velocities of particles A and B are given as VA = −10i+ 7j m/s and vß = 2i - 9j m/s. What is the…

Q: ans b please

A: Givenσx=45MPaσy=-60MPaτ=30MPa

Q: 5-79. The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter…

Q: 1- The fluid with constant density is called an: a. Ideal fluid b. compressible fluid c.…

A: Given the fluid with constant density

Q: (a) An 88-litre gas cylinder is filled with propane gas at a pressure of 1.15 MPa and 18°C. The…

Q: ater flows through a horizontal coil heated from the outside by high temperature flue gases. As it…

A: given

Q: Box of mass 10 kg resting on rough horizontal surface. Find friction force and normal force if…

Q: Find the cycle efficiency and specific steam consumption of a reheat cycle operating between…

A: This problem is related to the steam thermal power plant based on the Rankine cycle. efficiency is a…

Q: In the casting of steel under certain mold conditions, the mold constant in Chvorinov's Rule is…

A: Chvorinov's principle tells the amount of time required to solidify the molten metal in a mould…

Q: A liquid with specific weight of 15500 N/m³ is in the conduit shown. This liquid has zero viscosity.…

A: Specific weight of liquid, γ=15500 N/m3Pressure at A, PA=8 kPa=8*103 PaPressure at B, PB=5 kPa=5*103…

Q: n Question 1.2 A material has a modulus of elasticity E and a shear modulus of 0.4x E. The Poisson's…

A: Given data: Elasticity=EG=0.4E Need to determine the poison's ratio of the material.

Q: Q2: Air (y = 1.4) enters a converging-diverging diffuser with a Mach number of 2.8, static pressure…

Q: Selecting a proper pump for a service involves four primary areas to be considered for system…

A: The four important things to be considered before selecting the pump are, the total head or…

Q: 5.8 Show that for temperatures well below p, the mean free path of a phonon can be expressed as f…

Q: Longerons are used to oppose? a. Bending b. Tension C. d. Drag Compression

A: Longerons are members of aircraft structures.

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

Q: A pull effort of 25.9 N by a boy at the rope end which incircled to a large pulley will raise up the…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts…

Q: Answer should be in kJ Saturated liquid water at 60 ºC is heated until all the liquid becomes…

Q: *2-32. Determine the magnitude of the resultant force and its direction, measured counterclockwise…

A: Here, Magnitude of force F1 = 200 N Magnitude of force F2 = 150 N As we are given the angles…

Q: force F1= 2i – 6k {kN) is applied at the position 3j + 5k {m}, meanwhile another force F2 = - i + 4j…

Q: Saturated liquid water at 2.0 MPa is throttled to 20 kPa. Determine the fraction of water evaporated…

A: GivenP1=2MPa at Saturated liquid waterafter throttled P2=20kPa

Q: A disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0…

Q: In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of 0.4…

Q: x Slide 1 X Final exam (Remotely Procto #lockdown Question 1.16 The state of stress at a point is…

Q: Q2/ For a 97.5 wt% Fe-2.5 wt% C at a temperature 700 oC, determine the following: a) The Number and…

Q: 2.2 Among two horizontal parallel plate 10mm apart one plate is moving horizontal and other…

Q: Block C starts from rest and moves downward with a constant acceleration. Knowing that after 10 s…

A: Given Data The velocity of the block A is: vA=456 mm/s The time after which the block A moves is:…

Q: Velocity of a particle is given by v = -4t+ 20 m/s where t is in seconds. What is its acceleration…

A: Given: The velocity profile, v = -4t+20 m/s The time, t = 10 s

Q: frictionless piston-cylinder contains 42 kilograms of Acetylene having a pressure of 22 bar at 320…

Q: There is an equipment that allows to measure the heat transfer in fins with at least three different…

A: Given data: Fins of circular cross-section are considered.The fins are made of aluminum with…

Q: A composite sample of carbon reinforced epoxy has dimensions of 12 in x 12 in x 0.25 in and mass of…

Q: helllo, where did the 5.035Hz, come from? i di the calculation and am getting 11.25Hz

A: Given: The mass attached to the spring, m = 5kg The stiffness of spring, k = 25 kN/m The…

Q: Compare single threaded and multiple threaded screw and state the benefit why it has been…

A: Comparision: Single threaded screw: 1.It has only one continuous thread all over the body. 2.For…

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: Q3/A/ During AJM, the mass ratio is 0.75, Calculate mixing ratio, if the ratio of density of…

Q: A bar of 24-mm diameter and 400-mm length is acted upon by an axial load of 38 kN. The elongation of…

Q: This atom arrangement may cause metal brittleness. None of the above Hexagonal closed packed Body…

A: Given

Q: Calculate the rotational inertia of a meter stick, with mass 0.508 kg, about an axis perpendicular…

Q: ornal aBi=k(-200cessed), 3- If the acceleration of point G is ag = (-261-45.0)) m/s2, determine the…

A: To find: The vertical reaction at point C, Cy = ?

Q: For the system of parallel forces, determine the magnitude, direction, and the position of the…

A: Dear student, According to the guidelines i am allowed to answer only one…

Q: Based on the figure, solid alpha is liquid a+liquid eutectic point temperature a B+liquid 100% A…

A: Concept: 1.Given phase diagram is eutectic phase diagram. 2.Eutectic point is the point at which…

Q: Q4-/A/ During orthogonal cutting operation of material has shear strength 95.5 Mpa. The cutting…

Q: Q3/A/ During AJM, the mass ratio is 0.75, Calculate mixing ratio, if the ratio of density of…

Q: 11. Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the…

Q: A Japanese spacecraft Hayabusa-2 landed on an asteroid Ryugu on 21st February 2019 in an attempt to…

A: Given questions: Write down the rocket equation and determine at its maximum momentum the fraction…

Q: Why is alloying done? Using a Pb-Sn or Cu-Zn phase diagram, explain how you c achieve a 30% wt of…

A: Metals (or a metal plus a nonmetallic element) are heated until they are molten to make an alloy.…

Q: A mass M is under tension from wires CD and DE. If CD is 25º from the horizontal while DE is 30º…

A: The safe value of mass: m = 231.4068 kg

Q: The radius of the wheel is r=3 m. The tangential acceleration of the point on the edge of the wheel,…

Q: A vacuum of 42 kPa is measured in an airflow at sea level where the ambient pressure is 101.3 kPa.…

Q: A box weighing 150lb is moved across a horizontal Floor by dragging it by means of a rope attached…

A: Whenever the surfaces of two bodies are in contact there will be limited amount of resistance to…

Concept explainers

Forms of Energy

Energy is described as the capability to accomplish a task, like the ability to push a block by applying force on it. It is a quantitative property that is used to accomplish work on an object.

Question

ft3
min
5. A two-stage compressor receives air at 100 at 10psia and the
discharge pressure is 200 psia. If the temperature of the air received is
50F, find the intercooler pressure, total compressor work and total heat
rejected at the intercoolers. 44.72psia; 16.31 hp; 345.80 Bu
min

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A two-stage air compressor has an intercooler between the twostages, as shown in Figure. The inlet state is 100 kPa, 290 K, andthe final exit pressure is 1.6 MPa. Assume that the constantpressure intercooler cools the air to the inlet temperature, T3 = T1.It can be shown that the optimal pressure is P2 = (P1P4)1/2 forminimum total compressor work. Find the specific compressorworks and the intercooler heat transfer for the optimal P2.
Answer the folloeing problems: A two-stage compressor takes air at 100kpa and 25C with volume flow of 0.123m3/s and discharges to 800kpa. What is the heat rejected(kw) by the intercooler? ANS. 14.82 A two-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 7500kpa. Find the heat rejected(kw) at the intercooler. ANS. 27.015
A one-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 7600kpa. Find the heat rejected(kw) at the intercooler. ANS. 0
A two-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 7500kpa. Find the heat rejected(kw) at the intercooler. Ans. 27.015 kw
The compressor used in a refrigeration cycle takes in saturated R-134a vapor at a pressure of 360 kPa and raises it to a pressure of 1.0 MPa. The compressor can be considered well-insulated and inlet and exit velocities are small. In steady-state operation, the mass flow is 0.048 kg/sec and the power requirement is 1450 Watts. Find the discharge temperature.
A single stage compressor is to compress 8.5m3/min from 98.56KPa to 985KPa. Polytropic constant is 1.3. How much is the savings in work in kW if this is converted in 2 stage compressor? complete solution tnx.
A one-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 8600kpa. Find the heat rejected(kw) at the intercooler. Ans:0 Provide solution
A 3-stage air compressor compresses air from 100kpa to 700kpa. Find the intercooler pressure between the 2nd and 3rd stage. ANSWER: 365.88 kpa
Water vapor enters an adiabatic turbine at a pressure of 8 MPa, a temperature of 600 ℃ and a speed of 100 m/s, and then a pressure of 50 kPa exits at a temperature of 150 ℃ and a speed of 160 m/s. The turbine power is 10 MW. According to this; a) The steam flow rate from the turbine b) Do you find the isanthropic efficiency of the turbine?
4. A two-stage compressor receives 0.35kg/s of air at 100kPa and 269K and delivers it at 5MPa. Find the heat transferred in the intercooler. a. 94.5 CHU b. 94.5 kW c. 94.5 hp d. 94.5 BTU/hr Please answer this immediately. Thank you!
The steam rate to a turbine for variable output is controlled by a throttle valve in the inlet line.Steam is supplied to the throttle valve at 1,700 kPa and 225°C. During a test run, the pressure atthe turbine inlet is 1000 kPa, the exhaust steam at 10 kPa has a quality of 0.95, the steam flowrate is 0.5 kg/s, and the power output of the turbine is 180kW. 1. What are the heat losses from the turbine? 2. What would be the power output if the steam supplied to the throttle valve were expandedisentropically to the final pressure?
A one-stage compressor takes air at 100kpa and 25C with volume flow of 0.123m3/s and discharges to 800kpa. What is the heat rejected(kw) by the intercooler?