A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induceE Snipping ToolOptionsNew D Mode -O Delay - X CaA : no stressSelect the snip mode using the Mode button or clickbutton.B : shear stressSnipping Tool is moving..C: tensile stressIn a future update, Snipping Tool will be movirhome. Try improved features and snip like usua& Sketch (or try the shortcutD: compressive stress

Solution:- Given, Steel bar=5mmheated from 15°C to 40°C

A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce * Snipping Tool Options New O Mode - Delay - A : no stress Select the snip mode using the Mode button or button. B: shear stress Snipping Tool is moving.. C: tensile stress D: compressive stress In a future update, Snipping Tool will be r home. Try improved features and snip like

A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce * Snipping Tool Options New O Mode - Delay - A : no stress Select the snip mode using the Mode button or button. B: shear stress Snipping Tool is moving.. C: tensile stress D: compressive stress In a future update, Snipping Tool will be r home. Try improved features and snip like

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

_Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C°) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 T1.2 195 3 35 Aluminium 300 18.9 4 30 90 Aluminium Steal 4m 2m
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
(a) (b) (c) Given, (i) area of Z100 x 100 x 8 = 15.39 cm2, %3D (ii) thickness of gusset plate = 10 mm (iii) nominal diameter of rivets = 16 mm, %3D (iv) permissible tensile stress = 150 MPa, and (v) as per IS : 800 (1984) for single angle, the net effective area = A, + KA, %3D ЗА, K = (3A, + A2) where, A, = effective cross-sectional area of the connected leg, the gross cross-sectional area of the A2 %3D unconnected leg
fxplam how the to tal stress at a be determined from the figure below distance z Com ground surface d1 layer 1 d2 layer 2 Iz layer 3 z - d1 - d2
If the gauge is made of a material having a yield stress equal to 200 Mpa, determine the minimum required diameter d. Using a Factor of safety (F.S=2)
Prove each of the following equations separately 30 0x - 270 ([1-sin() sin(³9)] y Exy| Oxx 30 cos 1+ sin sin 270 30 K cos() sin() cos(32) K₁ x 2.70 Stresses near the tip of a crack in an elastic material. Crack FIGURE COS
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
If the gauge is made of a material having a yield stress equal 200 MPa, determine theminimum required diameter d. Using a factor of safety (F.S. = 2)
For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear stress. Sketch such stresses in a two- element format. 60 MPa 90 MPa Lx 30 MPa
8 KN 2m 3m 6KN. Am 3m, 3m A B 2m 6KN cross-Section 300mm 150mm Only considering stresses that are normal to the cross-sections you're designing. Where omax is the maximum value of stress developing in the cross-sections. Calculate omax
904. To avoid interference, a link in a certain machine is de- signed so that its cross-sectional area is reduced one-half at section A-E, as shown in Fig. P-904. Compute the maximum tensile stress developed across section A-B if (a) the cross section of the link is 160 mm square and (b) the cross section is a circle 160 mm in diameter. Ans. (a) 75.0 MPa; (b) 85.3 MPa 80 mm P = 240 kN 80 mm B Figure P-904.
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod