A double angle tension member L5 x 3 x 1/4, is connected to a gusset plate with 7/8 inch diameter bolts as shown in the figure. The steel used has Fy = 248.8 MPa and Fu = 400 MPa. The service loads are 35 kips for dead load and 15 kips for live load. Gross area of L5 x 3 x 1/4. Determine the effective net area, in sq.in.

A double angle tension member L5 x 3 x 1/4, is connected to a gusset plate with 7/8 inch diameter bolts as shown in the figure. The steel used has Fy = 248.8 MPa and Fu = 400 MPa. The service loads are 35 kips for dead load and 15 kips for live load. Gross area of L5 x 3 x 1/4. Determine the effective net area, in sq.in.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.9P

See similar textbooks

Similar questions

1. An unsymmetrical flexural member consists of a 70 × 600 topflange, a 70 x 400 bottom flange, and a 12 × 180 web.a, Determine the Section Modulus.b. Determine the distance from the top of the shape to the horizontalplastic neutral axis.c. If A572 Grade 50 steel is used, what is the plastic moment MPy forthe horizontal plastic neutral axis?
The unbraced column length of Round HSS 18 x0.5 in A500 Grade C (Fy = 50 ksi) is 30 ft.Determine the design compressive strength of the column using the equations in Chapter E inPart 16 of the AISC Manual. Confirm your answer using the AISC Manual Table 4-5 (pages 4-84,New AISCM) and (pages 4-84, New AISCM). The column has pin supports at both ends ( i.e Kx= Ky = 1.0) columns. Lx = Ly = 30 ft
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
Calculate the service load capacity in tension for an L6x4x1/2 of A36 Grade 36 steel connected with 5/8-inch dia bolts in standard holes as shown in figure 2. The angle tension member is connected to a gusset plate, typical of truss joints. The gusset plate is the plate at the intersection of members to which they are connected. Use American Institute of Steel Construction Load and Resistance Factor Design, and assume the live load to the dead load ratio is 4.0.
An unsymmetrical flexural member consists ofa 3 x 30 in. top flange, a 3 x 20 in. bottom flange, and a 60 * 2 in web A. Determine the distance from the top ofthe shape to the horizontal plastic neutral axis. B. If A572 Grade 50 steel is used, what is the plastic moment Mp for the horizontal plastic neutral axis?
A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate with 5/8 in. diameter bolts, as shown in Figure below. The service loads are 35 kips dead load and 15 kips live load. Determine the adequacy of this member using AISC specification. Assume that the effective net area is 85% of the computed net area.
The given angle bar L125x75x12mm with Ag = 2269 sq. mm is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 stell with Fy = 248 MPa and Fu = 400 MPa, determine the nominal tensile strength based on gross yielding (kN), determine the effective net area of the tension member if the shear lag factor is 0.80, determine the ultimate tensile strength (kN) based on tensile rupture.
The section shown carries a total service tension load of 508 kNwith a dead to live load ratio of 2:3. If the tension member has a length of 3 meters and A36steel, determine the following: a. The effective net area b. The LRFD design strength c. The ASD design strength d. Is the section adequate? section: C15 x 40 value of S: 63
Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
1. An unsymmetrical flexural member consists of a 70 × 600 top flange, a 70 x 400 bottom flange, and a 12 × 180 web. a, Determine the Section Modulus. b. Determine the distance from the bottom of the shape to the horizontal plastic neutral axis. c. If A572 Grade 50 steel is used, what is the plastic moment MPy for the horizontal plastic neutral axis?
A 4 × 4 carries an axial compressive force caused by dead, live, and roof live loads. Lumber is No. 1 DF-L. CM = 1.0, Ct = 1.0, and Ci = 1.0. Find: The allowable column load for each load combination if the unbraced length of the member is a. 3 ft b. 6 ft c. 9 ft d. 12 ft
A built-up beam made from fastening two channels to a wide flange section carriesloads as shown. The fasteners are 12mm∅ bolts with allowable shear stress τ= 110 MPa. Forbearing, σb= 220MPa for single shear, and σb= 275 MPa for double shear. E=200 GPA. Fy=420MPa. 1. Determine the Moment of Inertia of the Section2. Determine the Moment Capacity of the section if fb≤280MPa.3. Determine the flexural stress at fiber 30 mm above Neutral Axis at distance 5 metersfrom the support at A.