A steel flask of 0.04 m capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?

A steel flask of 0.04 m capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

By actual measurement, the enthalpy of steam at 8 bar is found to be 3000 KJ/Kg. What is the quality of steam? If 500KJ/Kg of heat is added to this steam, what is the (i) Superheated temperature (ii) Degree of superheat (iii) Enthalpy of superheat?
A frictionless piston-cylinder contains 42 kilograms of Acetylene having a pressure of 22 bar at 320 degrees Celsius. Heating occurs at constant pressure causing the piston to move until the volume is tripled. Compute for the (a) heat, (b) change in internal energy, (c) change in enthalpy (d) change in entropy, and (e) the non-flow work. (f) If ΔPE = 0.2 kJ and ΔKE = 1.35 kJ, what is the steady-flow work?
The tank of a leaky air compressor originally holds 90 L of air at 33deg C and 225 kPa. During a compression process, 4 grams of air is lost; the remaining air occupies 42 L at 550 kPa. What is the temperature of the remaining in air in degree centigrade.
Attached Table gives experimental values of the molar enthalpy of nitrogen at 1 bar and 100 bars. Use this data to answer the following question about a nitrogen throttling process operating between these two pressures. (a) If the initial temperature is 200 K, what is the final temperature?
Thermodynamics problem. If I have water vapor at 125◦C inside a piston, what pressure is necessary to convert the vapor to liquid water without changing the temperature?
The specific enthalpy for steam at 5.18 bar and 523 °C is (to no d.p.] in (Insert units symbol) Use the prescibed Steam table Rogers and Mayhew.
SOLVE STEP BY STEP IN DIGITAL FORMAT 4. Consider saturated water in a fixed thermodynamic state with a pressure of 0.15MPa and a temperature of 384.5 K. Find the value of the enthalpy in that state.
In the engine of a car that uses petrol as fuel, when the piston is at its highest position, air at 10 bar and 100°C enters the cylinder. Without any change in the volume, ignition occurs, and the air temperature rises to 1500°C. What is the air pressure after the ignition? (Select the closest value)[Whenever necessary, assume air as an ideal gas and consider R = 287 J/(kg.K).]
1. Refrigerant R-22 with the mass of 2 kg is located inside the sealed container, initially saturated vapor at 6.8 bar. Heat was added to refrigerant and final pressure reached 20 bar according to pv=const. Neglecting the kinetic and potential energy changes determine: Internal energy change in [J] Heat added to the refrigerant in [J] and work done by fluid in [J]. 3.draw the Temperature-volume diagram showing all stages. 4.What do you think about the final stage condition? Is it gas, liquid-gas, or liquid stage? Use energy balance equation and find all unknowns using the NIST webbook.
Oxygen (molar mass 32 kg/kmol ) expands reversibly in a cylinder behind a piston at a constant pressure of 3.129 bar. The volume initially is 0.011 m3 and finally is 0.0327 m3; the initial temperature is 16.3 0C. Calculate the heat supplied during the expansion in the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as = 0.917 k J / k g K and molar gas constant as = 8,314 J / kmol K
Using the Steam Table shown, at initial pressure of 0.046 bar and final pressure of 0.107 bar, find the following: Δhf ; Δhg ; Δsf ; Δsg
2. Saturated steam at 100°C is heated to 350°C at constant pressure. Use the steam tables to determine: a. The pressure in bar. b. the required heat input (J/s) if a continuous stream flowing at 100 kg/s undergoes the process.