Answered: A steel is 10 mm diameter and 2 m long.…

A steel is 10 mm diameter and 2 m long. It is stretched with force of 20 kN and extends by 0.2 mm (Answer: 254.6 MPa and 100 uε)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.7P: A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the...

See similar textbooks

Related questions

Q: Q11: After complete combustion in a furnace, the mass fraction of exhaust gases are found as :…

Q: Q3: In iron whose base plaet is mad aluminum alloy is turn on : The time for the plate temperature…

Q: In a stream line steady flow, two points A and B on a stream line are 1 m apart and the flow…

Q: Determine the force P required to move the wedge to the right if the coefficient of static friction…

Q: ostream pressure, temperature, and Ma umber are 0.53 atm, 255 K, and 2.8, espectively. Determine the…

Q: Problem 1 Compute the shear and moment diagram of the given figure below. Show complete values in…

Q: Q1/ Water flow through an orifice meter at an empirical equation Re 0.35RE0 and a rate of 300*10°…

Q: A 0.2 kg collar is released with an initial velocity v at A to slide on the frictionless curved rod…

Q: Calculate the moment of inertia of the shaded area about the x-axis.

Q: A {m} kg disk of constant thickness and radius 9.4 m, initially at rest, is placed in contact with a…

Q: Discuss the turning moment diagram for a four stroke cycle internal combustion engine in one…

A: Given question: Discuss the turning moment diagram for a four stroke cycle internal combustion…

Q: A pitot tube directed into a water stream having a velocity of 2.7 m/sec. It has gauge difference of…

A: A pitot tube is inserted into a 2.7 m/sec moving water stream.The water mercury manometer has a…

Q: A direct extrusion process is used to reduce a cylindrical part that has a diameter of 5 inch and is…

Q: An Ideal Dual Combustion cycle operates on 500 gram of air. At the beginning of the compression, the…

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

Q: Whay would the coefficient of friction be?

A: Given data as per the question power =75 kwN=1000 rpmr1r2=1.75r1=1.75r2Mean radius=110 mm

Q: Problem 7.4 A thin uniform disc of 25 cm diameter with a cen- tral hole of 5 cm diameter runs at…

A: We know that a thin uniform disc with a centre hole of 5 cm diameter spins at 10000 revolutions per…

Q: 3. The motion of the particle along a straight line is governed by the relation a = t³ – 2t² + 7…

Q: compute the compressive stress

Q: Given that μ = 0.25Katm−1 for nitrogen, calculate the value of its isothermal Joule–Thomson…

Q: A room is well insulated apart from a single-glazed window measuring 1 m2 and 4 mm thick. The…

Q: 2. Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine…

A: fig: FBD ∑ME=030*6-RB*5+60*3.5-60=0RB=66 kN ∑Fy=0RE-30+66-60=0RE=24 kN

Q: A spherical tank has a diameter of 10 m. If the tensile stress of the tank is 16 MPa, find the…

A: Diameter of spherical tank. d=10 m=10*103 mmTensile stress of the tank, σ=16 MPaWall thickness of…

Q: Calculate the 2nd moment of area for a beam with a length of 200 mm, a width of 20 mm and a height…

Q: Draw the desired emissivity versus wavelength for an object to absorb energy from the sun and retain…

A: Solution is attached below

Q: Suppose that a = 1.21 m and b = 1.1 m . (Figure 1) Determine the moment of inertia for the shaded…

Q: Two steel columns P (LengthL end yield strength = 250 MPa) and a (length 2L and yield strength = 500…

A: find the ratio of buckling load of column P to that of column Q.

Q: ersed rectangular plate as shown in the figure. Free water surface Im b-3 m

A: Solution is attached below:

Q: For the rotational system shown in Figure P2.19, find the transfer function, G(s) = 62(s)/T(s).…

Q: Graph/Plot the outp

A: This type of problem can be solved by plotting the graph between time domain and its laplace…

Q: The smallest division on the main scale of Vernier calipers is 0.1 cm. Ten divisions of the Vernier…

A: True reading=main scale reading+vernier scale division*least count 10 division of vernier scale=9…

Q: When a horizontal roll vortex is pushed vertical, what is created?

A: The wind shear causes the air to have a horizontal rotation. The strong updrafts from the rising…

Q: Consider a regenerative vapor power cycle with two feedwater heaters, a closed one and an open one,…

Q: TS DIAGRAM

Q: 4. At the instant shown, the crank AB is rotating with a constant counterclockwise angular velocity…

Q: 6. The m kg crate shown in Figure 6 is hoisted up by the incline using the cable and motor M. For a…

Q: For a beam with a length of 200 mm, a width of 20 mm and a height of 3 mm, calculate the maximum…

Q: Determine the reactions at A and B for the beams loaded as shown

A: According to the details provided in the question, we need to calculate reactions

Q: where did 144 come from

Q: Q/ For the beam shown in the figure below, find deflection and rotation at point B. EI=12000 kN.m?.…

Q: For rotodynamic fluid machines of a given shape, and handling an incompressible fluid, the relevant…

A: The variables involved: The rotor diameter =D The volume flow rate through the machine =Q The…

Q: According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength…

Q: you did not derive an equation you only did an explanation thumbs down

Q: The cross-sectional area of the figure below is 0.5 in2. If E = 13 x 106 psi, calculate the total…

Q: Given ISO and EN as the international codes or standards, in what area of mechanical engineering…

A: Codes are set of rule approved by local , state or federal government. These are used for the safety…

Q: What is the value of the torsion constant for the beam cross section shown below? 60 mm 20 mm 20 mm…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m anc 45 cm respectively.…

A: we will use darcy's formula to calculate loss

Q: 5 The Howe roof truss shown is subjected to wind loads as shown. The wind loads are perpendicular to…

A: To resolve the forces into horizons and vertical components.

Q: For the system shown in figure. find the power that the turbine can extract. The discharge through…

Q: Using the float method in determining the velocity of water through a channel, the float velocity in…

A: Option b is correct.

Question

100%

A steel is 10 mm diameter and 2 m long. It is stretched with force of 20 kN and extends by 0.2 mm (Answer: 254.6 MPa and 100 uε)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A bar made up of two square sections , one of steel and the other of aluminium is shown in Fig.2 The bar is acted upon by a compressive force P. Determine the value of P if the total decrease in length of the bar is 0.3 mm . Take Esteel = 205 GPa and Ealuminium = 75 GPa .
The steel rails of a railroad track are laid in the winter at a temperature of 15 degrees fahrenheit with gaps of 0.01 feet between the ends of the rails. Each rail is 33 feet long. At what temperature will the rails touch end to end? What stress will result in the rails if the temperature rises to 110 degrees fahrenheit? Answer: 9,434.1 psi. I'm not sure how to come up with this answer. Could you help me work this problem out step by step please?
One spring is placed inside the other, not touching each other, and compressed between a pair of parallel plates until the distance between the plates is 40 mm. Make a neat detailed sketch of the spring and plate assembly. If G = 83 GPa for both springs, calculate the following: 1. The force applied to the spring assembly. 2. The shear stress induced in each spring. 3. The total strain energy stored in the spring assembly. 4. The stiffness of each spring. 5. The equivalent stiffness of a single spring that can be substituted in place of these springs.
A copper and steel wires are welded together at their ends. The original length of each is 50 cm with the total length of 100cm and each has a diameter of 0.78 mm. A mass of 10 kg is suspended from the combined wire. By how much will the combination stretch? Ycopper=100 GPa, Ysteel= 210 GPa.
Use the principle of Strain energy due to direct stresses strength of materials 2
A 200 x 100 x 50 mm steel block is subjected to a hydrostatic pressure of 15 MPa. The Young's modulus and Poisson's ratio of the material are 200 GPa and 0.3 respectively. What is the change in the volume of the block?
A copper cylinder with a length of 1.5 m and diameter of 4 cm undergoes compression. (refer to the image ) (a) What will be the bulk strain of the copper rod if pressure is applied to reduce its volume to 0.00089 m3? (b) How much pressure was applied to the copper rod? (c) Calculate the percent change in volume of the copper rod.
A 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C, the gap Δ = 4.6 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 34 MPa. Use α = 18.09 × 10-6 m/(m·°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
The wires AB and AC are made of steel, and wire AD is made of copper. Before the 150-lb force is applied, AB and AC are each 60 in. long and AD is 40 in. long. If the temperature is increased by 80F, determine the force in each wire needed to support the load. Each wire has a cross-sectionalarea of 0.0123 in2. Take Est = 29(10 3) ksi, Ecu = 17(10 3) ksi, fast = 8(10 6)>F, acu = 9.60(10 -6)>F.
The bronze bar 2.7 m long with a cross-sectional area of 415 mm2 is placed between two rigid walls. At a temperature of 8.1 °C, there is a gap Δ = 2.32 mm, as shown in the figure. Find the compressive force (in N) experienced by the bar at a temperature of 68.66 °C. Use α = 18 × 10-6 /°C and E = 80.71 GPa. Round off your answer to three decimal places.
Modulus of Elasticity, E (Young’s Modulus): E = σ/e e: Strain, unit-less σ : Stress, in N/m2 E : Young's modulus (Modulus of Elasticity), in N/m2
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and is made from a homogeneous material. The length (L) of the rod is 1.75 m and Young’s Modulus for the material (E) is 250 GPa. When the rod is placed under tension it experiences deformation and a stress (?) of 650 MPa. Calculate the following:(1) Strain energy (U) to 2 decimal places in Joules.(2) Strain energy per unit volume (U/V) in J/m3(3) The change in length ∆L to 2 decimal places in mm.(4) The strain (?) due to deformation to 2 significant figures. (show all work)