please send correct answer Q10 QUESTION 9A researcher is working on sustainable composites has developed an experimental composite (CFRP) that has a small amount of biodegradablematrix. During a lab accident, they have lost some directional properties values that they have measured experimentally. However, they found theirnotes that include information on the Poisson's ratio, the stiffness matrix, and the ratio of E2/E1. Using the information provided find the value of E1 inGPa.V12 = 0.34E2/E1 = 0.13Q11= 132.04 GPaQ12=2.52 GPaQ22=8.92 GPaQUESTION 10According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of thematrix is 64 then what is the volume fraction of the fibres in the composite?

Answered: Image /qna-images/answer/eb738766-96a4-4fcd-8d21-9c143ba440e6.jpg

According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of the matrix is 64 then what is the volume fraction of the fibres in the composite?

According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of the matrix is 64 then what is the volume fraction of the fibres in the composite?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 15% HOW LONG THE RUNWAY must before a plane to reach a takeoff velocity of75 m/sec if it can…

A: soln : - initial velocity = u= 0 m/s Final velocity = v= 75 m/s Let S is the distance of…

Q: each strength gain and relate its significance on Strength and Economy. The design strengths are:…

Q: A simple truss is subjected to 20 kN force at point A as shown in Figure 2. The reaction force at…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

Q: what table and column are you looking at to get 103 kj for the enthalpy , and how are you getting…

Q: Completely solve. Write legibly. determine the heat and nonflow work of the polytropic expansion of…

A: GivenP1=2.8MPaT1=340oCP2=0.76MPaT2=200oC

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

Q: Air at 30 °C and 110 kPa flows at 20 N/s through a rectangular duct that measure 160 mm x 320 mm.…

A: Given data Air temperature = 30°C = 30 + 273 = 303 K Air pressure = 110 kPa Flow rate = 20 N/s…

Q: A 1m^3 nitrogen gas was placed inside a piston cylinder arrangement with initial state at 200kPa and…

A: Given that: V1 = 1 m3 P1 = 200 kPa T1 = 150 oC P2 = 150 kPa It is required to determine change in…

Q: Process of forming metal powder by directing molten metal through an orifice after which it is break…

A: Process of forming metal powder by directing molten metal through an orifice after which it is break…

Q: Sintering temperature is approximately equal to melting temperature of a metal. Select one: True…

Q: Replace the force and couple system acting on the member shown by an equivalent resultant force and…

Q: Q2/: As shown in the figure, the Assumptions of the flow through the venturi is steady,…

A: (1) Draw the diagram of the venturi meter.

Q: A pipe with 8 cm intemal diameter, 9 cm outer diameter, 2 meter long, thermal conductivity 30Wimk is…

A: INTRODUCTION : The critical radius of insulation is the insulation radius that is used to reduce…

Q: What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in Fig.…

Q: 3. A pump draws water from an 8 in. suction pipe and discharges through a 6 in. pipe in which the…

A: Suction pipe diameter, d1=8 in =812ftDischarge pipe diameter, d2=6 in=612ftVelocity in discharge…

Q: Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a.…

A: Given Width, B = 1000 m Depth, Y = 2 m Conversion…

Q: 3. Three bars each made from different materials are placed between walls when the temperature is…

Q: Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50…

A: (a) Write the expression of relative roughness. k=εD

Q: 1- A particle moves along the x axis. Its position varies with time according to the expression x= -…

A: Given data The position of the particle is given byx = -4t + 2t2A) We have to find the displacement…

Q: . Determine its mass in kg.

A: To find mass in kg

Q: Using the float method in determining the velocity of water through a channel, the float velocity in…

A: Option b is correct.

Q: The 1-in thick disk shown below initially spins at 20 rpm about an axle held by a fork-ended…

Q: I just have one question to clarify. The given problem stated that in the part of value of…

A: To find : value of elastic modulus of steel and aluminum Is correctly used in solution or not

Q: Given the front view and top view, draw the sectional view of the object

A: According to the details provided in the question, we need a section view. I am using Solidworks to…

Q: Consider the following geometric series: 2 + 4 8 + - 16 +.... Identify a and r, find a formula for…

Q: 95 kPa and 20°C. If the maximum temperature in the cycle is not to exceed 2200 K, determine (a) the…

A: Calculated thermal efficiency

Q: Exp. 1/Laser ablation: 1- Explain the main principle of the laser abolition phenomena to manufacture…

Q: CI Answer of the following: 1. According to the SAE viscosity classification, the oil (SAE 40) is…

A: Ans: 1 ... It's false. The oil (SAE40) is higher viscosity as compared to oil SAE20 at same…

Q: Two steel columns P (LengthL end yield strength = 250 MPa) and a (length 2L and yield strength = 500…

A: find the ratio of buckling load of column P to that of column Q.

Q: A cantilever beam is subjected to an inclined force (P) as shown in Figure 1, the equilibrium normal…

Q: b) You are given a set of six links. The lengths of the links are as follows: 6.3cm,…

Q: A schilieren photograph of a bullet shows a much angle of 28.the air is at pressure of 97kpa and…

A: Given: Mach angle θ=280 P=97 kPa = 97000 Pa T = 16 C = 16+273 = 289 K k = 1.4 R = 287 J/kg-K

Q: 4- Determine the mass of air in a 2 m tank if the air is at room temperature, 25 °C, and the…

Q: 22. Verify that the motion defined by the velocity components v, = 3x3, vz = -4x,, vz = 4x2 - 3x, is…

Q: 1- The initial velocity of the block in position A is 30 m/s. Knowing that the coefficient of…

A: Dear student, I have derived a general expression for time. You can put any value of theta and get…

Q: A two-stage, double-acting compressor is to deliver 90 lb/min of air from 14.3 psia and 90 ̊F to a…

A: Given data, Mass flow rate of the air, m˙a=90 lb/min = 1.5 lb/s Pressure at state 1, P1 = 14.3 psia…

Q: Q4) A stoichiometric mixture of a hydrocarbon fuel C,H12 and air is burned in steady flow combustion…

A: Given: The fuel and air temperature at inlet, T1 = 25°C The product leaving temperature, T2 = 2200 K…

Q: A uniform rod AB of mass m = 6.4kg is welded at its midpoint G to a vertical Shaft GD. Knowing that…

Q: The tensile load on a rod stretched between two fixed points is 4500 N. The temperature is 25°C. The…

Q: 2-9. Determine the resultant force on the lever shown in Figure P2-9. 20° 20 lb 30 lb FIGURE P2-9

Q: 1. According to the SAE viscosity classification, the oil (SAE oil (SAE 20) at the same temperature.…

A: we will discuss SAE viscosity ratings

Q: 4- Determine the mass of air in a 2 m³ tank if the air is at room temperature, 25 °C, and the…

Q: A uniform rod AB of mass m = 6.4kg is welded at its midpoint G to a vertical Shaft GD. Knowing that…

Q: Consider a steam power plant that operates on a regenerative Rankine cycle and has a net power…

A: Given that: For the regenerative Rankine cycle, Turbine inlet conditions are P5 = 10 MPa, T5 = 500…

Q: 2. The banked turns at Talladega International Super Speedway are designed so a 1760 kg race car can…

A: (a) Draw the free-body diagram of the car.

Q: Consider a location where the wind blows at 15 m/s. 2 options with two rows of turbines…

A: INTRODUCTION : The first row and second row of turbines are provided in this problem. During a…

Q: 15% A POLICEMAN SEES A THIEF 50 M, AWAY. THE THIEF SNATCH A BAG AND RUNS 5 M/SEC AND THE POLICEMAN…

A: The time taken by the policeman to catch the thief: 16.67 second

Q: A simple truss is subjected to 20 kN force at point A as shown in Figure 2. The reaction force at…

Q: Increasing the frequency of the supply will: O Decrease the rotor speed at a certain load torque.…

A: INTRODUCTION : Induction motors are used on circuits with different voltages or frequencies than…

Question

please send correct answer Q10

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q#04 (a) : What are composite materials? Discuss the functions of Re-inforcing agent and matrix materials. (b) : Name different types of advanced fibres.
Alice is conducting a tensile test on continuous fiber alignment compositesamples. She found that the results are different in the longitudinal andtransverse directions of the samples. Explain why this happens with the aid ofdiagram.
Note: Read the question carefully and give me right solution according to the question. List three main classification of engineering Fibre-reinforced composites. Name one example of both the dispersed phase material and matrix phase material for each classification.
27e) What are called composite ? What are the constituents of composites? How are composite materials classified? What is the role of matrix material and base material in a composite?
A large-particle composite consisting of tungsten particles within a copper matrix is to be prepared. If the volume fractions of tungsten and copper are 0.70 and 0.30, respectively, a) Compute the modulus of elasticity of this composite in the longitudinal direction. (The upper limit) and the modulus of elasticity in the transverse direction. (The lower limit), given the data that follow. Modulus of Elasticity (GPa) Copper 110 Tungsten 407 b) If the cross-sectional area is 280 mm2 and a stress of 60 MPa is applied in this longitudinal direction, compute the magnitude of the load carried by each of the fiber (tungsten) and matrix (copper) phases.
Specifications require that a concrete mix contain 280 kg/m3 and have a water-to-cement ratio of 0.53. How much water should be used in the mix?
Q1) What does it mean when we say composites are notch sensitive? Q2) What are the differences between the static strength in metallic and composite structures? Q3) How is the fatigue behavior different between composite and metallic structures? Q4) Why do we need orthotropic analysis for composite laminates? Q5) What are "kink-band" failure modes? Q6) How does moisture impact tension and compression strength in composites? Q7) What is the difference between a design value and an allowable and how does variability in material properties impact this behavior?
a) Determine the modulus of elasticity of the fibers. b) Estimate their modulus of toughness. c) Estimate their modulus of resilience.
119) fiber orientation in composite material is (which)I. one-dimensional continuous fibersII. planar continuous fibers in the form of woven fabricIII. random discontinuous fibersA. only IB. I AND IIC. All of them D.II and III 121) Between the phases of the composite material, intermediate and intermediate phases are like which of the following?A. Direct adhesion between primary and secondary phasesB. Interphase formation between primary and secondary phases by addition of third component for adhesionC. Formation of interphase by dissolving primary and secondary gases at their own boundariesA. A and cB. Only aC. only cD.B.E. All
Compute the modulus of elasticity for a composite which uses High Modulus Carbon fibers and Polyester matrix. The volume fraction of fibers is 45 % and matrix is 55 %. Note-use chart in image
Boron coated with SiC reinforced aluminium containing 40 vol.% fibers is animportant high temperature, light weight composite material. Estimate the density,modulus of elasticity and tensile strength of composite parallel to the fiber axis. Alsoestimate the modulus of elasticity of composite perpendicular to the fibres.
Boron coated with SiC reinforced aluminum containing 40 vol.% fibers is animportant high temperature, light weight composite material. Estimate the density, modulus of elasticity, and tensile strength of composite parallel to the fiber axis. Also estimate the modulus of elasticity of composite perpendicular to the fibres.