A steel plate is subjected to a state of plane stress (E = 200 GPa and v = 0.29) of Oxx = 105 MPa, Oyy = -19 MPa and Oyy = 96 MPa. Calculate the axial strain, ɛ77, at this point inthe z direction, normal to the plate's surface. Provide your answer in microstrain, pɛ. You do not need to type the units.

Given Data: Young's Modulus E=200 Gpa=200000 Mpa μ=0.29 σx=105 Mpa σy=-19 Mpa τxy=96 Mpa

A steel plate is subjected to a state of plane stress (E = 200 GPa and v = 0.29) of xx = 105 MPa, Ory =-19 MPa and Oxy = 96 MPa. Calculate the axial strain, Ezz, at this point in the z direction, normal to the plate's surface. Provide your answer in microstrain, pe. You do not need to type the units.

A steel plate is subjected to a state of plane stress (E = 200 GPa and v = 0.29) of xx = 105 MPa, Ory =-19 MPa and Oxy = 96 MPa. Calculate the axial strain, Ezz, at this point in the z direction, normal to the plate's surface. Provide your answer in microstrain, pe. You do not need to type the units.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and ismade from a homogeneous material. The length (L) of the rod is 1.75 m andYoung’s Modulus for the material (E) is 250 GPa. When the rod is placed undertension it experiences deformation and a stress (?) of 650 MPa. Calculate thefollowing:(i) Strain energy (U) to 2 decimal places in Joules.(ii) Strain energy per unit volume (U/V) in J/m3.(iii) The change in length ∆L to 2 decimal places in mm.(iv) The strain (?) due to deformation to 2 significant figures
The state of plane strain at a point has strain components of Px = -400(10-6), P y = 200(10-6), and gxy = 150(10-6), Fig. a. Determine the maximum in-plane shear strain and the absolute maximum shear strain.