A steel shaft 2573 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.

A steel shaft 2573 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid steel shaft must not twist through more than 3° in a 6-m length whensubjected to a torque of 12 kN • m. (a) Find the diameter of the smallest shaft that can be used. (b) What is the maximum shear stress in the shaft of this diameter? Use G = 83 GPa for steel.
A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the inside diameter and the outside diameter of the shaft that meets these conditions. Use G = 83 GPa
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.