The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater =9.79 KN/m° and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changesis to be neglected.0.409 MPa0.125 MPaa. The energy added in meters and the powerdelivered in kilowatts to the water by the pump.b. The mechanical efficiency of the pump.P0.04meter Ø0.1meter Ø

Answered: Image /qna-images/answer/fc8ff394-5663-4f07-b07f-06651e3732e2.jpg

The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. a. The energy added in meters and the power delivered in kilowatts to the water by the pump. 0.409 MPa 0.125 MPa P b. The mechanical efficiency of the pump. 0.04meter Ø 0.1meter Ø

The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater = 9.79 KN/m and Pinput = 27.34 hp. Determine the following parameters, if losses and elevation changes is to be neglected. a. The energy added in meters and the power delivered in kilowatts to the water by the pump. 0.409 MPa 0.125 MPa P b. The mechanical efficiency of the pump. 0.04meter Ø 0.1meter Ø

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump delivers water, density =1000kg/m3, at a volume flow rate of 0.004256 m3/sec. If the head developed by the pump is 4.01 m, determine the fluid power in Watts. Take g=9.81 m/s2. State the answer to two decimal places.
A pipe has an initial radius of r1, which then changes to a radius of r2. The velocity of the water in the initial part of the pipe is v1. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? let r1=10cm let r2=6cm let v1=5m/s b) What is the volume flow rate in the pipe?
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from Ato B is 5 cfs. a) Determine the head loss in feet in PIPE 1 and PIPE 2 b) Determine the head loss in feet in PIPE 5 c) Determine the flow in the upper branch pipe Q2 in cubic feet per second d) Determine the total head loss in feet between the inlet A and the outlet D
(Q29) A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure intensity in large pipe is given as 14 N/cm2 and the flow velocity in the larger pipe is 2 m/s. Find:- (a) The rate of flow of water through a horizontal pipe. (b) Loss of head due to sudden contraction. (c) Pressure intensity in smaller pipe.
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
A circular cone-shaped container is filled with water at a level h0. At time t=0 a faucet is turned on and starts filling the cone with water at a constant flow rate Q. (a) Determine the expression for the variation of the level of water with time in terms of the initial level and volume (h0, V0) and the feed flow rate Q. (b) At what time will the water start to spill over if the cone was initially filled to 1/3 of the cone's total height? Determine a numerical value for the time in the case where the cone angle is 45o, h0=20cm and Q=2l/s.
Two water reservoirs, A and B are 8km apart and are connected by a 750 mm diameter steel pipe( f=0.02). Reservoir A is 10 m higher than reservoir B. If the pressure at B is 4 kg/cm^2 greater than at A, determine the amount and direction of flow of water inside the pipe. Disregard minor losses.
A horizontal Venturi meter is shown in Figure 8 to measure the flow rate of water in the mainpipe. The main pipe area and the throat area are 100 m2 and 50 m2 respectively. The pressureP1 is measured as 3000 kPa and the pressure in the throat is P2 = 50.0 kPa and assume, thedensity of water is 1000.0 kg/m3. Use Bernoulli’s Principle to: a) Determine the velocity V2 , m/s in the throatb) Determine the velocity, V1, m/s in the main pipec) Determine the flow rate Q, m3/s in the water mains.
Water from a reservoir is pumped over a hill through a 450 mm diameter and an absolute pressure of 1.0 kg/cm^2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m^3/s. frictional losses is discharge and suction pipe, and pump is equivalent to 1.5 m. The speed of the pump is 800 rpm. Determine the following: A. Water power of the pump B. New value of discharge if the speed of the pump is increased to 1000 rpm C. New value of head if the speed of the pump is increased to 1000 rpm D.New value of power if the speed of the pump is increased to 1000 rpm
Water of density ? =998.2kg/m3 flows through a fireman’s nozzle—a converging section of pipe that accelerates the flow. The inlet diameter is d1 = 0.100 m, and the outlet diameter is d2 = 0.050 m. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet (2). (a) Write an expression for the horizontal force Fx of the fluid on the walls of the nozzle in terms of the given variables. (b) Verify your expression by plugging in the following values: ?1 = 1.03, ?2 = 1.02, V1 = 3 m/s, P1,gage = 137,000 Pa, and P2,gage = 0 Pa.
A turbine is located at an elevation 200 m below that of the surface of the water intake. The friction loss in the pipeline leading to it is 8 m and the turbine efficiency is 90%. What is the power input delivered by the turbine to the turbine if the flow is 3.0 m^3/s in kW? a.5121.41 b.5690.45 c.5085.50 d.5650.56
In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%