A steel tape is 30-m long under a pull of 6.0 kg when supported throughout. It has a cross-sectional area of 0.035 cm2 and is applied fully supported with a 12-kg pull to measure a line whose recorded length is 308.32 m. Determine the correct length of the line if E = 2.1x106 kg/cm2

A steel tape is 30-m long under a pull of 6.0 kg when supported throughout. It has a cross-sectional area of 0.035 cm2 and is applied fully supported with a 12-kg pull to measure a line whose recorded length is 308.32 m. Determine the correct length of the line if E = 2.1x106 kg/cm2

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Related questions

Q: PROBLEM NO. 2 20 KN/m Using approximate method, calculate all support reactions E 8 m 5m

A: Using slope deflection mtdFixed end moment MAD=0 and MDA=0MDE=-wl212=-20×8212=-106.67…

Q: (a) How far below the water surface should a vertical square, 1.25 m on a side, be immersed so that…

Q: A 100 m tape is suspended between the ends under a pull of 200 N. If the weight of the tape is 30 N,…

A: Given: Length of tape, L = 100m Pull, P = 200N Weight of tape, W = 30N Required : Correct distance…

Q: A circular bar having 300 mm? area is subjected to axial loads as shown in figure . Find the value…

Q: 85 N 3m 93 N

A: Weight = 93N Horizontal force = 85N 1st we have to check block moves in upward or downward…

Q: 50 kN 100 kN B -6 m- 100 kN A 100* 307 kN

Q: Calculate the resultant force vector using the table and diagram below. Round your answers to 1…

A: (d) is the correct answer

Q: .A 50-m tape weighs 2 kg. Every time a measurement is performed, the tape is supported at its end…

Q: 7. Four turns of rope around a horizontal post will hold a 2000KN weight with a pull of 20 kN. a)…

Q: A 30m tape is supported only at its ends and under a steady pull of 8kg. If the tape weighs 0.91 kg,…

A: Introduction- The Tape correction(s) in surveying refers to the process of adjusting measurements…

Q: A 6-kg block moves in a smooth vertical slot as shown. A spring having an undeformed length of 0.50m…

Q: 7. Four turns of rope around a horizontal post will hold a 200kN weight with a pull of 20 kN. a)…

A: Given data: The number of turns of rope ,n=4 Pulling force ,T1=20 KN The magnitude of the weight, T2…

Q: 2. The 12 m. ladder weighing 37 kg is resting on a horizontal floor at A and on the wall at B making…

Q: From the given set of parallel forces shown. 40KN 60KN 100KN 60KN 50KN 2.5m 2.0m 4.5m 1.5m 1.5m…

A: For finding the resultant force we have to calculate ∑FY = 0

Q: horizontal force P acts on the top of the 30N block having a width of 25 cm and a height of 50 cm.…

A: The coefficient of the friction is of two types like static friction and kinematic friction. The…

Q: A 100 m tape is suspended between the ends under a pull of 200 N, If the weight of the tape is 3O N,…

Q: 6. A cubic tank is completely filled with water. What will be the ratio of the hydrostatic force…

Q: Q2 ) Determine the tensions at A and B if w, 400 lb/ft as shown in fig. below? 15 ft 10n

A: For calculating the tension at A and B the following steps are shown,

Q: Q1: Determine the magnitude and direction of the resultant forces in figure below? Fq= 500 N F,- 600…

Q: Q.2 Two blocks A and B are connected through a string. Weight of each block is 50 N. Coefficient of…

A: given- weight of each block=50 Ncoefficient of friction=0.3angle=30o

Q: A 30 m tape steel tape weighing 0.7 kg has a cross-sectional area of 0.03cm² and a standard length…

A: (1) The expression for the correction due to pull is given by, Here, CP is the correction due to…

Q: A circular bar having 300 mm2 area is subjected to axial loads as shown in figure. Find the value of…

A: Elongation in bar is given by,∆=PLAEwhere,P=loading,L=length of bar,A=Area of cross section,E=…

Q: EXAMPLE (1) A circular bar having 200 mm² area is subjected to axial loads as shown in Fig .Find the…

Q: 22. Two blocks A and B with masses m and 2m are in contact on a horizontal frictionless surface. A…

A: Solution;

Q: Q1: Determine the magnitude and direction of the resultant forces in figure below? F500 N F,- 600 N…

A: resultant magnitude = 454.95 N resultant direction = 9.02o in third quadrant explanation is given…

Q: A 30-m steel tape weighing 1.75 kg is of standard length under a pull of 4.55 kg, supported for full…

A: Given: The standard length of the tape is 30 m. The weight of the tape is 1.75 kg. The standard pull…

Q: A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to…

A: Given data: 30-m steel tape. w=0.04 kg/m pull=8.5 kg measured length=2465.18 m.

Q: A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2 mm? is used to…

A: L=85.95m Po =5.44kg A=2.5mm2 =0.025cm2

Q: W

Q: HW2: In Figure, block A weighs 500N and block B weighs 1000N. The coefficient of friction is 0.35…

Q: 2) A Triangular gate having a horizontal base of 1.30 m and an altitude of 2 m is inclined 45° from…

Q: 2. A 50-m tape weighs 2 kg. Every time a measurement is performed, the tape is supported at its end…

A: Given Information: Weight of tape Pull applied Distance between supports To find: Correction due…

Q: A weight of 5 kN resting on a smooth surface inclined 30° to the horizontal is supported by a load…

Q: A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full…

A: Given: The length of steel tape is 30 m. The weight of steeel tape is 1.45 kg. The standard pull is…

Q: -Compute the total elongation caused by an axial load of 100 kN applied to a flat bar 20 mm thick,…

Q: Determine the slope and vertical displacement of point A on the beam shown in the accompanying…

A: ∑V=0 Vc - 20 -10 = 0 Vc = 30 kN ↑ Bending moment at A = 0 Bending moment at B = -10 x 4 = -40 kN.m…

Q: A 20 kg cabinet is mounted on casters that are locked and slide on the rough floor (µk = 0.25)…

A: Acceleration : The rate of change of an object's velocity with respect to time is called…

Q: The rectangular framework shown in the next slide is subjected to the indicated non-concurrent…

Q: H.W. A circular bar having 200 mm? area is subjected to axial loads as shown in Fig. Find the value…

Q: A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and the…

Q: A jet of water 75 mm in diameter has a velocity of 30 m/s. It strikes a flat plate inclined 45…

Q: C. From the Figure, Deter 20 kN/m

Q: A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe.…

Q: A block is constantly moving horizontally due to a horizontal force of 50Kn. It is given that the…

A: P=50kN To find weight of block (W)

Q: An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: W The 50 KN block is on top of an inclined plane shown in the figure. Determine the weight (W) of…

Q: n the figure, compute the vertical and horizontal components of displacement of joint E produced by…

A: Solution: Considering the Diagram: ∑MA=0Dy×30=80×45+120×20Dy=200 kips∑Fy=0Ay=200-80=120 kips

Q: A 50-m steel tape weighing 0.035kg/m supported at its end points. and is used to measure a line is…

A: Given data Length of tape Weight of chain per meter run Pull Length measured

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

A steel tape is 30-m long under a pull of 6.0 kg when supported throughout. It has a cross-sectional area of 0.035 cm² and is applied fully supported with a 12-kg pull to measure a line whose recorded length is 308.32 m. Determine the correct length of the line if E = 2.1x10⁶ kg/cm².

Please include the complete solution

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In every measurement, a 100-meter tape is suspended at the ends under a pull of 15 kg. It isalso supported at 30 m and 75 m marks. If the tape is used to measure a 543.25 long line,determine the total correction due to sag? The tape weighs 5 kg.
A 50 m tape is supported only at its ends and under a steady pull of 8.5 kg was used to measure a bridge, recorded as 1000 m. If the tape weighs 0.98 kg, determine the correct measurement of the bridge.
A horizontal force P acts on the top of the 30 N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. a. What is the value of P for motion to impend? b. Is the motion will impend due to overturning?
A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to measure a line with a steady pull of 8.5 kg. If the measured length of the line is 2465. 18 m, determine the correct length of the line. Please include the complete solution
a 30 m steel tape was used to measure aline and the initial pull is 5.5 kg. Pull at time of measurement is 8 kg. Weight of tape is 0.05 kg/m. E = 2.1x106 kg/cm2. Cross section =0.04 sq.cm. Measured distance between twopoints = 471.450 m in an inclined surface having a gradient of 3%. Find the correct horizontal distance between the two points.
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
Distance is measured as 605.75m with a 50-m tape supported on quarters with a pull of 6.5kg. The standard pull of the tape is 5.2kg; its weight is 1.10kg, E=2.02x10^6 kg/sqcm, and the unit weight is 0.03kg/cubic cm. a. What is the correction due to tension? b. What is the total correction due to sag? c. What is the corrected length?
for figure A= 5lb; 45 degrees for figure B= 9lb; 90 degrees for figure C= 6lb; 150 degrees
Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m , h=7m , b=5 m) I need a solution within 40 min
The taped distance of a line is 86.67 meters using a 100 m. steel tape at a pull of 20 kg and temperature a 32°C. The tape is exactly 100 m. at a temperature of 28°C (supported throughout) and standard pull of 10 kg. If the coefficient of expansion of the tape is 0.00001 18, find the total correction for temperature.
a 50 m steel tape weighing 0.035 kg/m is constantly supported at mid- length and its end points, and is used to measure a line AB with a ready pull of 6.5 kg. if the measured length of AB is 1268.256 m. determine the total sag correction for the whole length measured.
Calculate the horizontal and vertical displacement of point B. Rod cross-sectional areas A = 1050 mm2 E=220 Mpa