2. A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2.5mm? is used to measure a horizontal distance of 85.95 meters supported at bothends. If the standard pull for the tape is 5.44 kg, what must be the applied pull in kg(normal tension) in order to have no correction at all. Use 9.81 m/s? as accelerationdue to gravity.

L=85.95m Po =5.44kg A=2.5mm2 =0.025cm2

A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2 mm? is used to measure a horizontal distance of 85.95 meters supported at bo ends. If the standard pull for the tape is 5.44 kg, what must be the applied pull in (normal tension) in order to have no correction at all. Use 9.81 m/s? as acceleratic due to gravity.

A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2 mm? is used to measure a horizontal distance of 85.95 meters supported at bo ends. If the standard pull for the tape is 5.44 kg, what must be the applied pull in (normal tension) in order to have no correction at all. Use 9.81 m/s? as acceleratic due to gravity.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
If F = 5 kN and θ = 30°, determine the magnitude ofthe resultant force and its direction, measured counterclockwisefrom the positive x axis.
22 A 220-kg block is resting on a 56 deg inclined plane with a coefficient of friction = 0.76. Find the required horizontal force P (kN) that is necessary to prevent motion DOWN the incline. ROUND OFF TO TWO DECIMAL PLACES.
Blocks A and B weigh 50 lb and 30 lb, respectively.Using the coefficients of static friction indicated, determine the greatest weight of block D without causing motion.
There is a cylinder X weighing 735.75 Newtons that is held against a smooth incline and is being supported by a weightelss rod Y at 20°. Calculate all the forces that is acting on cylinder X.
A beam with length L is fixed at both ends. It is loaded with a concentrated force P at L/3 from the first support. Draw the loading diagram. If the beam has a length of 10 m, cross section of 200x200mm, and force P is 10 kN, what is the deflection at midspan (in mm)?
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
What is the equivalent static force (in kips) if pseudo-acceleration is 2.34g and the weight of the vibrating structure is 75 kips?
A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to measure a line with a steady pull of 8.5 kg. If the measured length of the line is 2465. 18 m, determine the correct length of the line. Please include the complete solution
A cylinder weighing 400 lb is held against a smooth incline by means of the weightless rod AB in FIig. P-309. Determine the forces P and N exerted on the cylinder by the rod and the incline respectively.
A cylindrical tank 3.7 meters in diameter and 4 m. long, with its axis horizontal, is half filled with water and half filled with another liquid having a specific gravity of 0.829. Determine the location of the total hydrostatic force measured from the top of the tank. Round off to two decimal places.