A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is 49GP.. 12 mm 200 mm 900mm wide steel tire 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire

A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is 49GP.. 12 mm 200 mm 900mm wide steel tire 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 20P

See similar textbooks

Similar questions

An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What are the mass and the weight of the astronaut on the Moon, and on Mars? What is the ratio of the pressure exerted by the astronauts shoe on Earth to Mars?
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
Calculate the pressure increase that must be applied to water to reduceits volume by 0.8%. Bulk Modulus of elasticity of water, Ev = 2.14 GPa.
Panel AB is circular and retains a liquid with specific gravity of 1.6. It has a width of 4 feet perpendicular to the paper. It has a radius of 11 feet from its center as seen in the figure. If h = 5 feet, and a = 4 feet, determine the total hydrostatic force acting on panel AB in pounds. ANSWER : 14,359.153
The figure below shows a closed container holding water and oil. Air at 35 kPa below atmospheric pressure is above the oil. Calculate the pressure at the bottom of the container in kPa(gage).
A sealed box filled with a liquid show below can be used to measure the acceleration of vehicles by measuring the pressure at the top point A at the back of the box while point B is kept at atmospheric pressure. Obtain a relation between the pressure PA and the acceleration a.
To measure the pressure inside a pipe, a manometer is connected to it as shown in the figure below. the open side of the manometer is inclined at an angle of 35 degree C. The density of the fluid in the manometer is 800 kg/m3 and the density of air is 1.25 kg/m3. Determine a) The length L. b) The pressure in the pipe.
Considering the properties as shown, calculate the power needed to overcome viscous resistance. Remember from prior subjects: U, Velocity = Radius of the movable part x Angular velocity = (r)(ω) T, Torque = Force x moment arm, which is the radius of the movable part = F(r) P, Power = T(ω) 1 revolution = 2π ω = 2π(N) where N is revolution per unit of time
Not a graded question, its a textbook problem The figure below represents a cylinder C i (d = 11 cm) that is inside a hollow cylinder (d = 11.1 cm). The inner cylinder, with a mass of 30 kg and a length of 25 cm (L), is subjected to a pressure P of 50 kPa at its bottom, rising at a constant speed of 2.5 m/s. a) Determine the dynamic viscosity of the lubricating oil that must be placed in the space between the piston and the cylinder; b) Determine the kinematic viscosity knowing that it consists of a mixture of 3 L of oil A (specific mass of 880 kg/m 3 ) and 2200 mL of oil B (specific mass of 940 kg/m 3 ). Data: g = 9.81 m/s 2
Please show the complete solution. (Example: Conversion of Units) A rigid container is closed at one end and measures 8 in diameter by 12 in long. The container is held vertical and is slowly moved downward until the pressure in the container is 17 psia. What will be the depth of the top of the container from the free water surface?
A container is filled with different layers of various liquids, as shown in the figure,Determine: a) the pressure difference between the top surface and the bottom of the cylinder and b) the pressureabsolute at the bottom of the cylinder if the atmospheric pressure is equal to 100Kpa. solve step by step
Figure shows an example of a hydraulic accumulator, which is a device for reducing pressurefluctuations in a hydraulic line or pipe. The fluid density is ?, the plate mass is negligible, and theplate area is ?. All the given pressures are gauge pressures. Write down the equations of motion.