A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical pressure. The pressure vessel is fabricated from aluminum (E = 10,000 ksi; v = 0.33), and it has an inside diameter of 54 in. and a wall thickness of 1.00in. If the internal pressure in the cylinder is 600 psi, determine the expected strain gage reading in ue. \30° O 347 µE O 506 µE O 683 µE 445 με O 545 µE

A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical pressure. The pressure vessel is fabricated from aluminum (E = 10,000 ksi; v = 0.33), and it has an inside diameter of 54 in. and a wall thickness of 1.00in. If the internal pressure in the cylinder is 600 psi, determine the expected strain gage reading in ue. \30° O 347 µE O 506 µE O 683 µE 445 με O 545 µE

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a.18.2 MPa b.32.6 MPa c.20.5 MPa d.28.7 MPa
A cylindrical tank has an inside diameter of 5 inches and is subjected to an internal pressure of 500 psi. If maximum stress is 1,200 psi, determine the required thickness. A. 1.195 in C. 1.395 in. B. 1.595 in. D. 1.795 in
The head loss in 50 m long, 12 cm diameter pipe is known to be 6 m when liquid specific gravity is 0.9 and viscosity of 0.04N-s/m² at 0.06 m/s. Find the shear stress at the wall of the pipe. a. 31.78 Pa b. 63.2 Pa c. 126.4 Pa d. 15.8 Pa
Compute the stress in Mpa in a 90 cm pipe with a wall thickness of 9.50 mm if water fills it under a head of 70 m. a. 23.65 b. 32.53 c. 30.87 d. 27.67
An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
Hi, please calculate and plot the distrbution of passive pressure in front of the wall and active pressure behind the wall In Soil 1: cohesion, c =0 angle phi = 38 degrees bulk unit weight, Y = 18kN/m3 For Soil 2: cohesion, c =0 angle phi = 28 degrees bulk unit weight, Y(sat) = 20kN/m3
INDUCED LOADS ARE APPLIED ON THE GROUND SURFACE AS SHOWN. POINT LOADS: PA= 250KN PB= 175KN PC= 300KN LINE LOAD: Q1= 150KN/M Q2= 225KN/M DETERMINE: a. THE TOTAL VERTICAL STRESS INCREASE AT POINT A AT A DEPTH OF 5M DIRECTLY UNDERNEATH LINE AB.b. THE TOTAL VERTICAL STRESS INCREASE AT POINT O, 8M FROM A TO THE POSITIVE Y AXIS, PERPENDICULAR TO LINE AB AT THE SAME DEPTH.c. THE TOTAL VERTICAL STRESS INCREASE DIRECTLY AT A POINT BELOW THE LINE LOAD 1, PERPENDICULAR TO POINT O AT THE SAME DEPTH.
The center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one corner has coordinates (7, 18). All dimensions are in meters. The area carries a uniform pressure of 135 kPa. Estimate the stresses at a depth of 15 meters below the ground surface at each of the following locations: (0, 0), (0, 18), (7, 0), (7, 18), and (12, 28).a. Obtain the values by the Boussinesq methodb. Compare the results with those of the 2:1 methodc. Comment on the resultsHint: In the Boussinesq method, the equations attached can be used.
Calculate the effective vertical stress at point A in the soil profile shown below (g=10m/s2) a. 105.9kPA b. 93.7kPA c. 106.1kPA a. 159.1kPA
2(a): Describe the maximum shear stress theory of failure. (b): Describe the basis of the theory. (c): How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?
A thick cylinder 1 meter inside diameter and 7m long is subjectedto an internal fluid pressure of 40MPa. Determine the thickness of the cylinder ifthe maximum shear stress in the cylinder is not to exceed 65MPa. What will be theincrease in the volume of the cylinder? E=200GPa, μ= 0.30.
If the pressure differential between pipes A and B, is (-5) kPa. Determine the differential reading, h in centimeters.