PLEASE ANSWER Question 5The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 16 mm and an outer diameter of 400 mm.Answer savedWhen the vessel is pressurized to 5.6 MPa, determine the tangential stress in the cylindrical part of the vessel.Marked out of 1.00Select one:P Flag questionO a. 64.40 MPaO b. 56.62 MPaO C. 32.2 MPa.O d. 28.31 MPaPrevious pageNext page

Longitudinal Stress is the vessel has closed ends the internal pressure acts on them to develop a…

The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 16 mm and an outer diameter of 400 mm. When the vessel is pressurized to 5.6 MPa, determine the tangential stress in the cylindrical part of the vessel. Select one: O a. 64.40 MPa O b.56.62 MPa C. 32.2 MPa O d. 28.31 MPa

The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 16 mm and an outer diameter of 400 mm. When the vessel is pressurized to 5.6 MPa, determine the tangential stress in the cylindrical part of the vessel. Select one: O a. 64.40 MPa O b.56.62 MPa C. 32.2 MPa O d. 28.31 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The head loss in 50 m long, 12 cm diameter pipe is known to be 6 m when liquid specific gravity is 0.9 and viscosity of 0.04N-s/m² at 0.06 m/s. Find the shear stress at the wall of the pipe. a. 31.78 Pa b. 63.2 Pa c. 126.4 Pa d. 15.8 Pa
The velocity distribution near the solid wall at a section in a laminar flow is given by u = 5.0 Sin (5πy) for y ≤0.10 m. Compute the shear stress at y=0, (ii) y=0.06 m and (iii) y=0.12 m.. The dynamic viscosity of the fluid is 5 poise.
An open rectangular tank 6 m long, 3 m wide and 2m deep contains water to a depth of 1 m. It is accelerated horizontally at 2.5 m/s2 in the direction of its length. Determine the minimum pressure intensities at bottom Unit of the Correct Answer: kPa Group of answer choices 12.3 2.31 0.123 1.23 .
Q1: A: What will be the (a) gage pressure (bJabsolute pressure of water, at depth 14m below surface. Use (Pwater 1000 kg/m, PATM 101 kN/m3).
A concentrated load of 1000 kN is applied at the ground surface. Compute the vertical pressure a) at a depth of 4 m below the load, b) at a distance of 3 m at the same depth. Use Boussinesq's equation. Ans: a) 30 kPa, b) 9.8 kPa
A 300 mm cast-iron pipe is discharge 120 lit/sec. At a point 200 m from the reservoir the center of the pipe is 30 m below the reservoir surface. What is the pressure in kPa to be exerted there? Assume f= 0.02
Determine the absolute pressure at A in psi. Oil, SG = 0.824, a = 0.74 ft., b = 0.81 ft., c =0357 ft., Patm = 14.7 psi.
A closed cylindrical tank with 0.60 m diameter and 1.0 m height is fully-filled with water. The tank is rotated at 200 rpm. What is the pressure (kPa) at the circumference of the top base?
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find the the pressure intensity in kPa at the bottom of the tank. a. 30.41 b. 13.7 c. 34.34 d. 27.47
6.3 Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities at the half the diameter from boundary is 2 m/s. The local velocity at 20mm from the pipe wall is 1.5m/s and the flow is turbulent,
An inverted right circular conical tank loses water out of a 4-in hole at the bottom. The radius of the top of the tank is 8 ft and its total height is 20 ft. Assume that the coefficient of contraction is 0.6. Solve for dh/dt. Solve for dV/dt.