A strip footing is needed to carry a load of 100 kN/m at a depth of 1 m. Shear strength parameters for the soil are c = 0 and o = 36°. Determine the minimum width of footing for a factor of safety of 3 against shear failure. The water table may rise to the base of footing. Take G = 2.65, e = 0.6 and y = 16 kN/m3. %3D

A strip footing is needed to carry a load of 100 kN/m at a depth of 1 m. Shear strength parameters for the soil are c = 0 and o = 36°. Determine the minimum width of footing for a factor of safety of 3 against shear failure. The water table may rise to the base of footing. Take G = 2.65, e = 0.6 and y = 16 kN/m3. %3D

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Shallow Foundations: Ultimate Bearing Capacity

Section: Chapter Questions

Problem 6.14P: A 2 m 3 m spread footing placed at a depth of 2 m carries a vertical load of 3000 kN and a moment...

See similar textbooks

Similar questions

A 1.57 -m. deep 2.5 m. x 3.3c m. footing has to be constructed as shown in Figure 1. The soil properties are: γ=18.7 kN/m3 , γsat=20.9 kN/m3 , angle of friction is 29 degrees, and D1 = 0.55 m. Using FS = 3.3, determine the value of ultimate bearing capacity and the ultimate load capacity (inclined) using β = 17 degrees . (use: γw=9.81 kN/m3)
For a square footing, determine the gross allowable load, Qall, that the footing can carry. Use Terzaghi,s equation for general shear failure ( fs=3.5). Given : Density of soil above the underground table, p=1800 kg/m^3, saturated soil density below the underground table, P sat=1980 kg/m^3, c=24 kN/m^2, $=25°‌, B=1.8 m, Df=1.2 m and h=2 m.
Calculate the stress at the end of the clay stratum σ, and the increment Δσ that the footing produces a load P = 1200 KN, at points A and B C
Calculate the stress at the end of the clay stratum σ, and the increment Δσ that the footing produces a load P = 1200 KN, at points A and B C Use Boussinesq´s equation.
A circular foundation of 1.5 m diameter is constructed in a sand deposit. Given: Df =1 5 m, soil friction angle Ø =35o and soil unit weight γ =17 4kN/m3. Estimate the ultimate uplift capacity of the foundation.
A 3 m 4 m footing, founded at 2 m depth in a clay, applies a net pressure of 200 kN/m2. The bed rock lies 10 m below the footing. The modulus of elasticity of the clay is 30 MN/m2. Using Janbus generalized relationship [Eq. (17.1)], assuming undrained conditions and flexible footing carrying uniform pressure, estimate the expected settlement.
Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
It is required to design a cantilever retaining wall to retain a 5.0 m high sandy backfill. The dimensions of the cantilever wall are shown in Figure 15.52 along with the soil properties. Check the stability with respect to sliding and overturning, based on the active earth pressures determined, usinga. Coulomb's earth pressure theory (δ' = 24°), andb. Rankine's earth pressure theory.The unit weight of concrete is 24 .0 kN/m3
The 2.5 m x 3.5 m rectangular spread footing placed at a depth of 1.5 m supports a vertical load of 4000 kN and a moment of 400 KN-m, as shown in Figure 2. Determine the factor of safety, against bearing capacity failure, using Meyerhof’s effective area method.
A square footing which carries an axial load of 13000 kg has its bottom resting on a ground water table at a depth of 2.5 m from the ground surface. Nc = 35, Nq = 22, Nγ = 19. Take PDRY = 1910 kg/m3 and PSAT = 1600 kg/m3, c = 1800 kg/m2. Compute the net soil pressure.
A square footing 2.8 m X 2.8 m is built on a homogeneous bed of sand of density 18 kN/m3 and ϕ = 36o. If the depth of foundation is 1.8 m, determine the safe load that can be applied on the footing.
Consider a continuous foundation of width B = 1.4 m on a sand deposit with c' = 0, Φ' = 38° and γ = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 4.31). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination β = 18°. Estimate the failure load Qu(ei) per unit length of the foundation a. for a partially compensated type of loading [Eq. (4.85)] b. for a reinforced type of loading [Eq. (4.86)]