(a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push button will be pressed, motor will turn off and will remain in off state until 1" push button is pressed again.

(a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push button will be pressed, motor will turn off and will remain in off state until 1" push button is pressed again.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Want to see the full answer?

Check out a sample Q&A here

See Solution

Similar questions

Draw a symbol for a solid-state logic element AND.
Need Part B (a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. 2. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push…
) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action. Major Topic 12 Basic logic gates & its application AN
24) Which of the following elements does not affect how a ladder logic program is developed?A) The contact type and active state of the input field devices.B) The type, direct or inverse acting, and active state of the output field devices.C) The requirement for current sinking or sourcing inputs and outputs.D) The choice of normally-open and normally-closed instructions for the PLC program.
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.
Using Simple Logic Gates. Given: A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) To Find: Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight Note: Construct Truth Table. Draw Logic Diagram. Simplify Boolean equations using K-Map. Use Basic Logic Gates.
A manufacturing plant needs to have a horn sound to signal quitting time. The horn should beactivated when either of the following conditions is met:1. It’s after 5 o’clock and all machines are shut down.2. It’s Friday, the production run for the day is complete, and all machines are shutdown.Design a logic circuit that will control the horn. (Hint: Use four logic input variables torepresent the various conditions; for example; input A will be HIGH only when the time of day is 5o’clock or later)
Sketch 3-input XOR/XNOR functions using DCVS (differential cascade voltage switch) and CPL (complimentary pass transistor logic), compare their speed, power, area, and explain your answers
A limited company has four directors A, B, C, D holding 35%, 30%, 20% and 15% of the shares respectively. A major decision must have a support of minimum 60% of the stock. Design a combinational logic circuit for the voting in the company. Use a decoder to design the circuit. Show the truth table of the circuit.
B) A coin-operated cold drink dispenser will provide cold drink (D) under the following conditions: The correct coin (C) is inserted AND A paper cup is in position (P) AND The selector is set t Orange (O) OR Sprite (S) OR Lemonade (L) Write the Boolean expression for the output of the dispenser. Represent the operation of the dispenser in logic circuit 4 get a logic circuit to mimic aorporate checquing system for operatore of a compnny