volume flow rate requirement of 21it/s with anof60К Pa.A system hasaindexrunΔΡFindanappropriatepumpfromthemanufacturer's catalogue gives the following information for acentrifugal pump operating at 24rev/s:kPaQ lit/s98.76 0.595188.76 1.58068.38 2.55538.76 3.5Two geometrically similar pumps are running at the same speed of1000r.p.m. One has an impeller di ameter of 0. 4m and discharge of301/s against a head of20m. If the other pump gives half ofthis discharge rate,determine the head, diameter and power ofthe second pump.

A system has a volume flow rate requirement of 2lit/s with an 60k Pa. Find an appropriate pump index run AP of from the manufacturer's catalogue gives the following information for a centrifugal pump operating at 24rev/s: p kPaQ lit/s 98.76 0.5 95 88.76 1.5 80 2 68.38 2.5 55 38.76 3.5

A system has a volume flow rate requirement of 2lit/s with an 60k Pa. Find an appropriate pump index run AP of from the manufacturer's catalogue gives the following information for a centrifugal pump operating at 24rev/s: p kPaQ lit/s 98.76 0.5 95 88.76 1.5 80 2 68.38 2.5 55 38.76 3.5

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.
A centrifugal pump operating under steady flow conditions delivers 2,813 kg/min of water from an initial pressure of 86,976 Pa to a final pressure of 296,902 Pa. The diameter of the inlet pipe to the pump is 19.82 cm and the diameter of the discharge pipe is 11.28 cm. What is the work in J/s?
A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at the best efficiency point, find the pump impeller diameter, pump speed, the best efficiency value of the pump, the head at the best efficiency value, and the specific speed of the pump, given that CQ=0.15 CH=6 CP=0.75.
1. A centrifugal pump delivers 900 ?3/ℎ? of sea water (sp.gr.= 1.03) from a source wherethe water level varies 2 m from high to low tide level. The pump centerline is located2.6 m above the surface of the water at high tide. The pump discharges into theatmospheric surface condenser, 3 m above the pump centerline. Loss of head due tofriction in the suction pipe is 0.8 m and that in the discharge side is 3 m. Pump is directlycoupled to a 1750 rpm, 460 volts, 3 phase, 60 Hz. Calculate: a) total dynamic headb) pump theoretical powerc) power to drive the pump if pump efficiency is 82%
A centrifugal pump operating under steady flow conditions delivers (2000 + K) kg/min of water from aninitial pressure of [100 + (K/2)] kPa to a final pressure of [1000 + 2K] Pa. The diameter of the inlet pipe tothe pump is 20 cm and the diameter of the discharge pipe is 8 cm. What is the work done? IMPORTANT NOTE: K=821
The performance data of a water pump follow the curve fit Havailable = H0 = aV^2, where the pump’s shut off head H0=5.30 m, coefficient a =0.0453 m/(Lpm)^2, the units of pump head H are meters, and the units of V. are liters per minute (Lpm). The pump is used to pump water from one large reservoir to another large reservoir at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure. The system curve simplifies to Hrequired =(z2- z1) + bV ^2, where elevation difference z2 =-z1 = 3.52 m,and coefficient b =0.0261 m(Lpm)^2. Calculate the operating point of the pump.
The performance data of a water pump follow the curve fit Havailable = H0 − aV.2 , where the pump’s shutoff head H0 = 7.46 m, coefficient a = 0.0453 m/(Lpm)2 , the units of pump head H are meters, and the units of V. are liters per minute (Lpm). The pump is used to pump water from one large reservoir to another large reservoir at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure. The system curve simplifies to Hrequired = (z2 − z1) + bV.2 , where elevation difference z2 − z1 = 3.52 m, and coefficient b = 0.0261 m/(Lpm)2 . Calculate the operating point of the pump (V.operating and Hoperating) in appropriate units (Lpm and meters, respectively).
Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device is a single stage, single-acting air compressor. Air delivery for thisdevice is 30 bar at a speed of 1500 rev/min. The atmospheric condition of his locationis 87 kPa and 20 ˚C, with a FAD of 0.22 m2/min. The clearance volume is 4% of the swept volume and the stoke/bore ratio is 1.3/1. Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the delivery isothermal efficiency of the compressor percentages to 2 decimal places?
3. A centrifugal pump has d1 = 7 in., d2 = 13 in., b1 = 4 in., b2 = 3 in., 1 = 25, 2 = 40 and rotates at 1160 rev/min. If the fluid is gasoline at 20C and the flow enters the blades radially, Estimate the theoretical (a) flow rate, in gpm; (b) the water horsepower; and (c) the head in ft. b. flow rate Answer : _______________ gpmc. water horsepower Answer : _______________ HPd. head Answer : _______________ ft
Explain and Plot the process why the Height(H) arrive in meter(m) unit and the Velocity of water arrive in meter per second (m/s) unit. "A boiler feed pump has a suction enthalpy of 2500 KJ/kg and exit of 2505KJ/kg"
An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal places.
A centrifugal pump operating under steady flow conditions delivers 2,270 kg/min of water from an initial pressure of 82,740 Pa to a final pressure of 275,800 Pa. The diameter of the inlet pipe to the pump is 15.24 cm and the diameter of the discharge pipe is 10.16 cm. What is the work done? a. 458.1 kJ/min b. -458.1 kJ/min c. 438.4 kJ/min d. -438.4 kJ/min