Example: In a 45° bend a rectangular air duct of 1 m² cross-sectional area is gradually reduced to 0.5 m² area. Find the magnitude and direction of force required to hold the duct in position if the velocity of flow at 1 m² section is 10 m/s, and pressure is 30 kN/m². Take the specific weight of air as 0.0116 kN/m³. Solution: Fay 45° Fex PA, cos 45° 45° V,cos 45° Y Pi

Example: In a 45° bend a rectangular air duct of 1 m² cross-sectional area is gradually reduced to 0.5 m² area. Find the magnitude and direction of force required to hold the duct in position if the velocity of flow at 1 m² section is 10 m/s, and pressure is 30 kN/m². Take the specific weight of air as 0.0116 kN/m³. Solution: Fay 45° Fex PA, cos 45° 45° V,cos 45° Y Pi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 20 ° C fl ows at 30 gal/min through the 0.75-indiameterdouble pipe bend of Fig. P3.154. The pressuresare p 1 = 30 lbf/in 2 and p 2 = 24 lbf/in 2 . Compute the torqueT at point B necessary to keep the pipe from rotating.
An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in 88 seconds . The trajectory measures yield x = 2.4m and y = 1.37m . Assuming the area of the opening is 25cm2, Calculate Coefficient of Contraction, Coefficient or Velocity
Oil (SG = 0.89) enters at section 1 in Fig. P3.20 at a weightfl ow of 250 N/h to lubricate a thrust bearing. The steady oilfl ow exits radially through the narrow clearance betweenthrust plates. Compute ( a ) the outlet volume fl ow in mL/sand ( b ) the average outlet velocity in cm/s.
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and external of tube are equal to 60 cm and 90 cm respectively. The tube should be drowned-approximately 1.5 meter below the lowest tail race level and draft tube high of 600 cm. The velocity at the exit is 1.5 meter per second. (Friction head loss in draft tube = 0.034 m ), calculate:- Find the pressure head at the entrance and the bottom in m of water and in Kg / cm?. the total heads at the same point with reference to the tail race as a datum find the power at the entrance and bottom the efficiency of a draft tube
The pipe bend of Fig. has D 1 = 27 cm and D 2 =13 cm. When water at 20 ° C fl ows through the pipe at 4000gal/min, p 1 =194 kPa (gage). Compute the torque requiredat point B to hold the bend stationary.
A wind tunnel test section is 3 ft square with fl ow propertiesV = 150 ft/s, p = 15 lbf/in2 absolute, and T = 68°F.Boundary layer blockage at the end of the test section is8 percent. Find the angle, length, exit height, and exit pressureof a fl at-walled diffuser added onto the section toachieve maximum pressure recovery.
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
In an industrial cooling process, water is circulated through a system. If water is pump from the first floor through a 6cm diameter pipe with a speed of 0.45 m/s under a pressure of 400torr, what will be the pressure on the nest floor 4m above into a pipe with diameter 2cm? Show your solution
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.