A system is described by the differential equation dy(t) + y(t) = cos(t) %3D dt with y(0)=1. The output y(t) of the system is given by A. y(t) = (;cos(t) +sin(t) –et) u(t) B. y(t) = (cos(t) -e) u(t) C. y(t) = (cos(t) +sin(t) u(t) e--)u(t) %3D - | %3D D. y(t) = (cos(t) + sin(t) + %3D Select one: O A. ОВ. O C. . O D. .

A system is described by the differential equation dy(t) + y(t) = cos(t) %3D dt with y(0)=1. The output y(t) of the system is given by A. y(t) = (;cos(t) +sin(t) –et) u(t) B. y(t) = (cos(t) -e) u(t) C. y(t) = (cos(t) +sin(t) u(t) e--)u(t) %3D - | %3D D. y(t) = (cos(t) + sin(t) + %3D Select one: O A. ОВ. O C. . O D. .

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.16P

See similar textbooks

Similar questions

If G(s) = 1 / (s + 2), find the response c(t) if the input r(t) = u(t), a unit step, assuming zero initial condition.
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system
When the unit step function is applied to the input of the system whose block diagram is given below, the output response takes the value c (0.2) = 0.11 for t = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate.
Let x(t) be defined as?(?)={3, −1≤?≤0, {1, 0<?≤1, {0, ????. Sketch the following:
The response of a system, h(t) is given as in Figure 1 below where the amplitudeof this signal is 7. Then,this system is excited by an input of x(t) = (u(t) × (u(-t)+u(t))) /1. 1)Illustrate the input signal, x(t). 2)Calculate the convolution output of the system y(t) = x(t) ∗ h(t). Nextdetermine y(t) when t is 1 sec 2)Prove the solution in Q2 is comparable when solving in frequency domain(Laplace). Next, sketch the signal for convolution output.
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear?
Graph the following functions for the given x[n]= {…,0,2,-2,0,1,3,-2,-3,1,-1,0,…} signal. a) y[n]=x[n](u[n+3]-u[n-2])-2∂[n]+3∂[n-3]x[n b) y[n]=2x[-n]+(x[n])²+x[-n+2]
Examine the stability of the system given by the characteristic polynomial Δ(s)=2s^3+4s^2+ s+1 using the Routh-Hurwitz criterion.
Given the plant transfer function, G(s) = 90/ s(s+4) and H(s) = 1. Obtain (i) characteristic equation (ii) damped frequency of oscillation (iii) damping ratio (iv) settling time (v) delay time
Given the following ordinary differential equation describing the dynamics of a system y'''+17y''+80y'+100y=3(u''+5u'+4u) Here, y(t) is the output and u(t) is the input. Laplace table is given below. Find the transfer function G(s) [=Y(s)/U(s)] by applying Laplace transform (all initial valus are zero) Find the poles and zeros of the system. Is the system stable or unstable? Which pole(s) is/are slow and which ones is/are fast? Find Y(s) if input is unit step function. Find initial and final values of the system by applying the theorems.
a) Y(ω) = 1/(5+jω) The expression above defines the frequency domain signal Y(ω) from a time domain signal y(t) i) Determine the imaginary & real parts of Y(ω). ii.Determine the signal y(t) that produced the signal Y(ω). b)What are the 3 areas of application of i.Signals ii.Systems c) Briefly summarise with explanation the difference between discrete & continuous time signal and also write an expression that describes each signal type.
Find f(t) for each of the following functions. 1. F(s)=320s2(s+8). 2. F(s)=80(s+3)s(s+2)2. 3. F(s)=60(s+5)(s+1)2(s2+6s+25). 4. F(s)=25(s+4)2s2(s+5)2.