A system of computer aided tools used by operator in electric utility grid to? A plan B optimize C) check D) analyze

Q: need the answer quickly

A: 1. In an outward flow reaction turbine, water enters the runner from casing. Yes, It's true.…

Q: p. Determine the second moment of the shaded area (area moment of inertia) around the x-axis and…

A:

Q: 600 lb 800 lb 1500 lb | 400 lb B. D. 3 -5 ft- FIG. P4.27

A: Given

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A:

Q: Directions: Answer the given questions. ho1. What is the relationship between decision-making and…

A: Statistical judgments are made based on observations of a phenomena that is subject to…

Q: A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

A: A 300 mm venturimeter is known to be installed in a vertical pipe transporting water moving upward.A…

Q: Gas oil at 210 °C is to be cooled to 30 °C and its flow-rate is 20,000 kg/h. The temperature…

A: Energy that comes in” includes heat flux from external sources by conduction, convection and…

Q: A wheel barrow is used to lift a 200 Ib load. The length from the center of the wheel to the center…

A:

Q: Q3) If in a standard vapor-compression cycle using refrigerant 22 the evaporating temperature is…

A:

Q: strain at failure in

A: Given; Compliance of the UTM is constant and is given by 5×10-8m/NDetermine the strain at failure in…

Q: sphere is placed over the three closely packed identical spheres on a horizontal plane. All the…

A:

Q: For the given machine part, where the cross-sectional area at m-n is a square with side 5 mm,…

A: The largest allowable value of the distance: e = 11.6667 mm.

Q: - CALCULATE REACTIONS FINT ALL MEMBER FORCES. INDICATE ALL LOADS AND () TENSION OR C) COMPRESSION…

A:

Q: For the given Mohr's circle where o, = 40 MPa,try = 40 MPa, (i) what is the maximum shear stress…

A: Given data Stresses given are:σx = 40 MPaτxy = 40 MPa

Q: 1. Calculate the length of time a 950-watt blow dryer would have to blow on an iron pipe (0.75 cm…

A:

Q: Whoop- ニフ P:?

A:

Q: -Find Taylor or Maclaurin for the following functions: 1) f(x) = sin 3x

A:

Q: 3. Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A: The shaft is as shown below, For equilibrium, TA+TD-TC=0TA+TD=TCTA+TD=750 N.m     ............. 1…

Q: Summarise and discuss the concepts and applications of Design for Additive Manufacturing (DfAM)

A: Given question: Summarize and discuss the concepts and applications of Design for Additive…

Q: Heat transfer problem.In a counter flow heat exchanger, water, flow rate 0.05kg/s, enters at 400K…

A:

Q: A certain gasoline engine is modeled as a monatomic ideal gas undergoing an Otto cycle, represented…

A:

Q: 9. A Proell governor has three fly balls, each of mass 4 kg. The lengths of all the arms are mm and…

A: Given Data The mass of the each fly balls are:m=4 kg The lenght of each arm is:L=280 mm=0.28m The…

Q: A 100 x 300 mm ammonia compressor with a compression efficiency of 82% operates with a suction…

A: Given, bore of the compressor  , d = 100 mm stroke of the compressor , L = 200mm Condenser pressure…

Q: You have an office building with a 25,000 sf vacancy. You have two proposals:

A: Introduction Expense stops are operating expenses paid by the landlord, operating expenses beyond…

Q: n a Refrigerant 12 system which serves a 212 kw evaporator at - 30 0C. The system uses two stage…

A:

Q: 5. 1) If block A has a mass of 1.5 kg, determine the largest mass of block B without causing motion…

A: Find the largest mass of the block B.

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

A: Given t=30mm P=2.5MPa D=8m=8000mm n=900 d=20mm

Q: Construct a circuit drawing of a hydraulic dump lift using an open center circuit.

A: To construct an open center circuit of a hydraulic pump

Q: 1. What are the modeling methods in engineering

A: It's a structured approach for supporting the requirements, design, analysis, verification, and…

Q: A Kaplan turbine develops 1500 kW under a head of 6 m. The turbine is set 2.7 m above the tailrace…

A:

Q: 1. Given the data as shown in the figure, determine the (a) maximum torque Tmax (N-mm) that maybe…

A:

Q: Q3) If in a standard vapor-compression cycle using refrigerant 22 the evaporating temperature is…

A:

Q: A В

A:

Q: particle is moving along a straight line with a = (12t - 3t^0.5) ft/s^2, where t is in seconds.…

A:

Q: (+) А 12 mm В с 750 N-m 125 mm 25 mm 200 mm D 300 mm

A:

Q: E A bead with a mass of 0.25 kg is released from rest at A and slides down and around the fixed…

A: Given data as per the question Mass =0.25 kg Calculations considering point A as the datum apply…

Q: 8,038 N m) flows through the pipeline (Figure C2). . Gasoline (specific weight y Calculate the flow…

A:

Q: differential pitot tube located at the center of a cylindrical air tube produces 2.6 in. of water…

A: Solution is attached below:

Q: The figure shows a small piece of clay colliding into a disk. The disk is initially at rest, but can…

A:

Q: 3.) A supply of 50 kg of chicken at 6 C contained in a box is to be frozen to -18 C in a freezer…

A: Given             Mass, m = 50 kg Temperature, T1 = 6oC                       T2 = -18oC Specific…

Q: determine the moment of inertia about the y-axis

A:

Q: What is the extension speed of the cylinder in ft/s for the meter-in circuit shown in the figure?…

A: Given data as per question Load =2908 lbsPiston area =3.7 in2=0.0256944 ft2Rod area = 1.4…

Q: A rectangular plate with a V-notch is shown in Fig. 2.29. Model the plate using triangular elements…

A: Given : To find : Model the plate using triangular elements

Q: If the viscosity of water at 70 °C is 0.0042 poise and its specific gravity is 0.97, determine its…

A:

Q: A recuperator is a heat exchanger positioned in the exhaust gases in order to recover the waste…

A: Given data: 1 Shell 2 Tube (1S-2T) pass heat exchanger Hot fluid inlet temperature T1=483 K Hot…

Q: The 4 kg box shown in the figure start from rest at t = 0 in which the friction is negligible.…

A: Givent=0t=1sm=4kgF=9.81N

Q: Summarise and discuss the differences between CNC programs (G-code programs) for CNC machining and…

A: Given question: Summarize and discuss the differences between CNC programs (G-code programs) for CNC…

Q: A barrel contains a 15 cm layer of oil of density 5.88 kN/m3 floating on water that is 30 cm deep.…

A:

Q: m. Determine the resultant force

A: To find Resultant force the water exerts on Side A of the tank.

Q: Q2) A Carnot refrigeration cycle absorbs heat at -12°C and rejects it at 40°C. (a) Calculate the…

A: