A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that the distance between the gage marks became 50.122mm. a,) What is the modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axial stress of the specimen? Solution must have Free Body Diagram/drawing.

A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that the distance between the gage marks became 50.122mm. a,) What is the modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axial stress of the specimen? Solution must have Free Body Diagram/drawing.

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter15: Ferrous Metals

Section: Chapter Questions

Problem 21RQ

See similar textbooks

Similar questions

A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that the distance between the gage marks became 50.122mm. a,) What is the modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axial stress of the specimen?Note: Please show detailed solutions with illustrations.
Define the Thomas (1968) Elastic Modulus from CPT ?
Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 50*10 deep reinforced with bars 20-mm in diameter enclosed with 10-mm-dia stirrups when the tensile steel strain is 0.008 and concrete compeession strain is 0.003. f’c = 20 MPa express your answer in 2 decimal places only in mm
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.
A metal specimen with 20 mm diameter and 100 mm gauge length is loadedelastically with 5 kN and elongates 0.8 mm. Its diameter under this load is 19.95 mm. Calculate:a) the Bulk Modulus, Kb) the Shear Modulus, G
A 100-foot-long surveyor’s steel tape with a cross-sectional area of 0.006 square inch must be stretched with a pull of 16# when in use. If the modulus of elasticity of this steel is , (a) what is the total elongation in the 100 foot tape and (b) what unit tensile stress is produced by the pull?
A water tank is 8 meters in diameter and 12 meters high. Ifthe tank is to be completely filled, determine the minimumthickness of the tank plating if the stress is limited to40 MPa.
A wite with circular base of radius 3 mm was subjected to tensile stress of 13.5 Pa. if half the amount of stress is to be applied to a wire with square base if 1.52 mn width, what must have been the force (in newton) applied to this new wire?
If the bulk modulus of elasticity for water is 2.2 GPa, what pressure is required to reduce a volume by 0.6%?
Consider a bar with a rectangular cross-section area with a thickness of t = 0.5 in. and height of h = 3.5 in. When force P = 19 kips is applied to the bar, the strain gages attached to the surface of the bar reads εx = 740 µε along the direction of the force and εy = -170 µε in the perpendicular direction. Determine Poisson's ratio for this specimen? Determine the modulus of elasticity for this specimen?in Ksi
(a) Define centroidal axes, principal axes and neutral axes with the help of diagrams. When do these axes coincide? (b) Define longitudinal and hoop stresses in a thin walled in thin walled pressure vessels. Support your answer with neat sketches. (c) Define strain gauge. Discuss strain rosettes and its various types. (d) Define Kern of a section. Derive the general equation for finding the kern of a section.
STRENGTH OF MATERIALS answer: 17.68 kN and 11.8 MN/m2 compressive *what is the solution to this problem?