A thick-walled cylinder of inner diameter 270 mm is.constructed of a high strength low-alloy steel of yield stress 574 MPa. When the cylinder is subjected to an intemal pressure of 185 MPa it yields to a diameter of 310 mm. Determine (a) the outer radius of the thick-walled cylinder and (b) the additional internal pressure required to cause the cylinder to burst.

A thick-walled cylinder of inner diameter 270 mm is.constructed of a high strength low-alloy steel of yield stress 574 MPa. When the cylinder is subjected to an intemal pressure of 185 MPa it yields to a diameter of 310 mm. Determine (a) the outer radius of the thick-walled cylinder and (b) the additional internal pressure required to cause the cylinder to burst.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cylinder head of a steam engine is subjected to a pressure of 1 N/mm2. It is held inposition by means of 12 bolts. The effective diameter of the cylinder is 300 mm. A softcopper gasket is used to make the joint leak proof. Determine the size of the bolts sothat the stress in the bolts does not exceed 100 MPa
What does the Hooke’s law involve?
How can the stresses acting in the thin-walled pressure vessels be analyzed?
What is the answer? AQuestion A or B?
The gas tank is made from A-36 steel (σYield= 440 MPa) and has an inner diameter of 1.5 m and a wall thickness of 21 mm. If the tank is designed to withstand an internal pressure of 8.5 MPa, determine the factor of safety against yielding using the maximum-shear-stress (Tresca) theory.
Determine the bursting steam pressure in kPa of a steel shell with diameter of 12 inchesand made of ¼ inch thick steel plate. The joint efficiency is at 70% and the tensile strength is60 ksi with factor of safety of 4.
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?
he region of safety in maximum shear stress theory contains which of the given shape *
' A rylindrical boiler with hemispherical ends has an outside diameter of 6 ft. lf the hoop and axialstresses in the boiler must be limited to 15 ksi and 8 ksi respectively, determine the thickness of steel plate required if the internal pressure in the boiler will be 200 psi.
A cylinder which can be considered as a thin-walled shell, is made of steel plate 16 mm thick and is 2.14 m internal diameter. The cylinder is subjected to an internal fluid pressure of 0.55 MN/m2 gauge and, at the same time rotated about its longitudinal axis at 3000 rev/min. Determine:(a) the hoop stress induced in the wall of the cylinder due to rotation:(b) the hoop stress induced in the wall of the cylinder due to the internal pressure:(c) the factor of safety based on an ultimate stress of the material in simple tension of 456 MN/m2. Steel has a density of 7.8 Mg/m3.
The storage tank shown contains liquefied propane under a pressure of 1.4 MPa at a temperature of 38 °C . Knowing that the tank has a diameter of 315 mm and a wall thickness of 2.8 mm determinethe maximum normal stress and the maximum shearing stress in the tank.
A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 420 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa.