A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is then 805.407 in3. If the water is released from the tank, how many pounds will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk modulus of elasticity

A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s volume is then 805.407 in3. If the water is released from the tank, how many pounds will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk modulus of elasticity

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Related questions

Q: A cylindrical tank having a base radius of 500 millimeters and a height of 2500 millimeters is…

Q: 5. A certain gas weighs 0.12 lb/ft at a given temperature and pressure. Determine: a. Density b.…

A: Given The specific weight of gas γgas=0.12 lb/ft3 The specific weight of air γair=0.07651 lb/ft3

Q: Darcy' Law A fluid's viscosity and unit weight are reduced to 60% and 80%, due to increase in…

A: Due to an increase in temperature, a fluid's viscosity and unit weight are reduced to 60% and 80%.

Q: F₁=MN lb 60° F₂=SN lb As shown in the figure above, find the value of the following: 1. FR lb 2. The…

Q: Calculate dynamic viscosity of a cm/sec. liquid having specific gravity of 1.2 and kinematic…

Q: A plate of size 60 cm x 60 cm slides over a plane inclined to the horizontal at an angle of 30°. It…

A: We will apply force balance

Q: A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire…

Q: Calculate the weight of block A shown in the figure.' 37 36 N W.

Q: 1) 10 cu.m. OF Kerosene oil weighs 8000kg. Calculate its specific weight, density and specific…

A: Note- We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: A cylindrical container with a diameter of 1.0 m and a height of 2.0 m weighs 294N. If the container…

Q: A cylindrical tank having a base radius of 500 millimeters and a height of 2500 millimeters is…

Q: Using the formula uploaded in the image below, find the h1 and h2 values if: K= 2.1875 X 10-3 cm/s…

A: Falling head Permeability Test- It is a method of finding permeability of fine grained soil such as…

Q: What is the pressure on a fish 13.8 m under the ocean surface? (Density of ocean water = 1025…

Q: A cylindrical tank having a base radius of 500 millimeters and a height of 2500 millimeters is…

A: To Determine 1. What is the unit weight of the liquid in the tank? N/m^3 2. What is the density of…

Q: 1. A cylindrical bucket 60 cm in diameter and 50 cm high weighing 150 N contains oil (s=0.80) to a…

A: D=60cm h=50cm

Q: (Buoyancy) An irregularly shaped piece of a solid material weighs 8.33 lb in air and 5.30 lb when…

Q: A man weighs 210 lbf at a location where g= 32.10 ft/s2. Determine his weight on the Mars, where g=…

A: Given data- Case-1 Weight of man (W) = 210 lbf g=32.10 ft/s2 Case-2 On mars- g=5.47 ft/s2 Weight =…

Q: Determine the Bulk modulus of elasticity of a liquid, which is compressed in a cylinder from a…

A: The bulk modulus of elasticity is defined as the ratio of increase in pressure with respect to that…

Q: Water is at a given pressure of 100 kPa and a temperature of 207 C. The tables give values at…

A: To find the specific volume at a temperature of 207 C use the formula of interpolation :…

Q: A liquid has a specific weight of 41.5 lbs/ft3. How much will a cylinder that measures 18” tall and…

A: The specific weight of liquid = 41.5 lbs/ft3 Height of cylinder = 18" = 1.5 ft Diameter of cylinder…

Q: Problem 18- A brass cube 6 in on a side weighs 67lb. We want to hold this cube in equilibrium under…

A: The side of cube = 6 in = 0.5 ft The volume of cube =Vc = 0.5×0.5×0.5 = 0.125 ft^3 The weight of…

Q: if you push a 20 kg mass with a force of 40 N. what will be the object's acceleration 40m/sec^2 O 20…

Q: 80 cm Ø water Wtank+water = 500 kg Wempty = 60 kg 200 cm

Q: If the friction force on the 6 kg object is 10 N. Find the coefficient of friction force ?

Q: The outside diameter of a right circular cylindrical tank is 3,000 mm and its height is 6,000 mm. If…

Q: Calculate the pressure at a point 337 mm below the surface of the mercury in a vessel. Express the…

Q: (Buoyancy) An irregularly shaped piece of a solid material weighs 8.33 lb in air and 5.30 lb when…

Q: 5. A block weighs 22-N in water and 30-N in oil (sg=0.82) when suspended fully submerged. Calculate…

Q: In Figure below, calculate Fx and Fy per unit width of the cylinder

A: Given Radius of cylinder = 1.5m Diagram To find Fx and Fy per unit width of cylinder

Q: determine the density(lb/ft3) of a cubical body whose side is equal to 1.19 in and has a mass of…

A: step 1-

Q: 16 An empirical pressure-density relationship for water is given as Pa 2001x - 2000 (Here, suffix…

A: Given, and, 1atm is equivalent to 100kN/m²

Q: converts the density of 1650 kg / m3 to density in pounds mass over ubic foot (Ib/ ft3)

A: 1kg =2.204lb

Q: Four steel bars jointly support a mass of 15 Mg as shown. Each bar has a cross-sectional area of 600…

Q: Calculate the pressure increase that must be applied to water to reduce its volume by 0.8%. Bulk…

Q: Determine the load that can be lifted by the hydraulic system shown in the accompanying figure. All…

A: Pressure= (Force / Area) Let F1= 1000N F2 = load applied at other end

Q: Question 2 The pressure difference between 2 points is 100,000 Pascals of a fluid column with height…

Q: A sphere 1.5m in diameter floats half submerged in tank of oil (SG=0.80). What is the total weight…

A: Buoyancy force isFB=1243π0.753 γoilWeight of sphere isWS= 43π0.753 γS

Q: A 400-gram package lying on a horizontal surface is attached to a horizontal string which passes…

Q: From the figure shown, determine the specific gravity of the log if the length is 6 m and the radius…

Q: 4.) A homogeneous solid cylinder (SG = 0.60), 1 m high and 3 m diameter floats with its axis…

Q: The specific gravity of a material is 5.4 What are its specific weight in US units? Answer: 5400…

Q: Calculate the pressure at a point 50 mm below the surface of the oil in a vessel. Express the answer…

A: Figure is as shown

Q: the ratio of container diameter to tube diameter is 8. When air in the container is at atmospheric…

A: Given : Container diametertube diameter=8 When air in container is at atmospheric pressure, free…

Q: A tape of 20m length is used to measure a distance 1980 m at a temperature 35 °C under 20 N tension…

A: Given Data Length of the tape=20 mThe diatance measured=1980 mTemperatureTm=35°CTension ForceT1=20…

Q: 400 G 200 G A 400 GRAMS LYING ON A HORIZONTAL SURFACE IS ATTACHED TO A HORIZONTAL STRING WHICH…

A: To find Coefficient of static friction between the 400 g mass and the surface.

Q: 1. An object weighs 100 N in the air and 25 N when submerged in water. Calculate its volume and…

Q: Q2// Determine the specific weight, density and specific gravity of a liquid that occupies a volume…

Question

A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’s
volume is then 805.407 in3. If the water is released from the tank, how many pounds
will be collected at atmospheric pressure? Use 305 000 psi as an average value of bulk
modulus of elasticity

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
Show complete solution with figures A rigid container having outside diameter of 30 mm and thickness of 5 mm contains water of height 700 mm.What will the column length be if a force of 5 kN is applied to its open end by a frictionless plunger? Assume noleakage. Use 2.2 GPa for bulk modulus of elasticity of water. a) 689 mm b) 525 mm c) 527 mm d) 695 mm e) None
Calculate the pressure increase that must be applied to water to reduceits volume by 0.8%. Bulk Modulus of elasticity of water, Ev = 2.14 GPa.
A copper wire is 1.0 m long and its diameter is 10 mm. If the wire hangs vertically, how much weight must be added to its free end in order to stretch it 3.0 mm?
2 only and answer 3 decimal A closed empty steel cylindrical tank 2m in diameter 3m high is to be used as a buoy in fresh water. (1) What would be the volume of the concrete cube placed inside the tank if the tank would be submerged 2m into the water? The steel tank weighs 500kg. Use Sconc. = 2.4. (2) what is the weight of the concrete cube?
Problem 18- A brass cube 6 in on a side weighs 67lb. We want to hold this cube in equilibrium under water by attaching a light foam buoy to it. If the foam weighs 4.5lb/ft^3, what is the minimum required volume of the buoy?a.) 1.02 ft^3b.) 2.02 ft^3c.) 3.02 ft^3d.) 4.02 ft^3e.) 5.02 ft^3f.) 6.02 ft^3
A rectangular box is floated. Outer dimensions 2m by 10m and has 2m high sides and weighs 4.9N. It carries a load of 4.9N. It is launched in a pool of water with density 1 g/cm3. How much (in m) of the boat submerged (actual draft)? Provide the answer in appropriate precision (significant digits).
A container holds two layers of different liquids, one fluid having a specific gravity of 1.1 is 30cm deep and the other fluid having a specific gravity of 1.6 is 40cm deep. A solid cubical metal having an edge dimension of 18cm and specific gravity of 6.5 is submerged such a manner that half of the cube is on the top layer and the other half in the bottom layer of fluids with the square base of the cube horizontal. Help me compute the weight WCUBE of the cubical metal in newtons, compute the buoyant force BFCUBE in newtons acting on the metal object, and compute the tension T in newtons in the wire holding the cube to maintain its position. please draw a figure
A solid brass sphere of volume 0.305 m3is dropped in an ocean, where water pressure is 2 x 107 N/m2. The bulk modulus of water is 6.1 x 1010 N/m2. What is the change in volume of the sphere?
In Figure below, calculate Fx and Fy per unit width of the cylinder
A hollow cylinder 2.46-m in diameter and 7-m long weighs 3,159 N. How many cubic meters (m3) of metal weighing 112 kN/m3 must be placed inside the cylinder such that 2.9 m. of the cylinder is protruding above the liquid surface? The hollow cylinder is submerged in a liquid that has a specific gravity of 2.3. Round off to four decimal places.