A thin walled tube has a pentagonal cross-section as shown in the figure. Note that the figure is hollow and the red shade denotes only the area bounded by the median line. If one side of the pentagonal shaded area is a = 469 mm, determine the torsional stress in MPa. Use Torque, T = 44 kN-m, thickness, t = 9 mm, shear modulus, G = 78 GPa, and length, L = 10 m. a a a

A thin walled tube has a pentagonal cross-section as shown in the figure. Note that the figure is hollow and the red shade denotes only the area bounded by the median line. If one side of the pentagonal shaded area is a = 469 mm, determine the torsional stress in MPa. Use Torque, T = 44 kN-m, thickness, t = 9 mm, shear modulus, G = 78 GPa, and length, L = 10 m. a a a

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

The 2 m long tube, the cross section of which can be seen in the figure, is fixed at one end and a torque of 700 N.m is applied from the other end. Since the wall thickness of the tube is 3 mm, calculate the shear stress values at points a and c. Calculate the angle of rotation of the end of the tube where the torque is applied.
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
Refer to Figure 10.46. A flexible circular area of radius 6 m is uniformly loaded. Given: q = 565 kN/m2. Using Newmarks chart, determine the increase in vertical stress, z, at point A. Figure 10.46
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
The rectangular bar shown in the figure is subjected to a uniformly distributed axial loading of w = 11 kN/m and a concentrated force of P = 14 kN at B. Determine the magnitude of the maximum normal stress in the bar and its location x. Assume a = 0.9 m, b = 1.1 m, c = 20 mm, and d = 35 mm.