A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L, C = 31mm 16A (100 x 75 x 8) mm L Choose the nearest correct statements: L = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm

A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L, C = 31mm 16A (100 x 75 x 8) mm L Choose the nearest correct statements: L = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.4P

See similar textbooks

Similar questions

Note: Hi, pls need help. Any solutions are highly appreciated. I will rate this right away. Thank you in advance! What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan (rounded value) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Given: Fy=248 MPa w=29.76 Kg/m A=3787.09 mm^2 Ix=32.84×10^6 mm^4 Iy=1.17×10^6 mm4 Zx=317.91×10^3 mm3 Sx=258.92×10^3 mm3 Zy=44.25×10^3 mm3 Sy=21.47×10^3 mm3 S= 6 m RLL=900 N/m^2 RDL= 900 N/m^2
4. Considering sag rods and tie rods at midspan, what is the required diameter of sag rods in mm? (rounded value) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of 185 kN applied along its centroidal axis. The maximum size of fillet weld that can be used in 8mm and the allowable shear stress of 94 MPa. Determine the lengths of the side fillet welds if a transverse fillet weld is added at the end of the angle. 71 mm 185 KN 29 mm
A 50 mm x 100 mm purlin is used for a roof truss. Spacing of trusses is 3.5 m Weight of roofing sheets is 120 Pa Roof live load is 750 N/m² of roof area and ceiling load is 140 N/m² of roof area Spacing of purlins is 450 mm on centers. Inclination of the top chord is 30° from the horizontal The timber is 80% stress grade yakal. From table, E(yakal)=9780 MPa. Neglect the weight of purlins. 1. Which of the following most nearly gives the total vertical load, in N/m? a. 455 b. 193 c. 270 d. 338 2. Which of the following most nearly gives the maximum bending stress, in MPa? a. 15.6 b. 5 c. 12.5 d. 33.5 3. Which of the following most nearly gives the maximum deflection, in mm? a. 33.5 b. 16.3 c. 47.5 d. 24.8
Note: Hi, pls need help. Any solutions are highly appreciated. I will rate this right away. Thank you in advance! What is the required diameter of sag rods? Considering sag rods and tie rods at third points (rounded value) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
Determine the location y¯ of the centroidal axis x¯−x¯ of the beam's cross-sectional area. Neglect the size of the corner welds at A and B for the calculation. Take r = 61 mm . Express to three significant figures and include the appropriate units.
The vertical member shown in Figure STCN17.02 consist of two angles welded to the 8-mm thick gusset plate. Given the following data: Angle size: 75 mm x 50 mm x 6 mm (long legs back-to-back) Area of one angle = 738 mm Size of weld = 6 mm Yield strength of steel, Fy = 248 MPa Allowable weld shear stress, F, = 124 MPa a = 25 mm a. Determine the safe capacity of the vertical member in kN. b. If P= 185 kN, determine the length of weld L2 (mm) such that each weld have equal shear stress. Neglect end returns. c. If L1 = 140 mm and L2 = 70 mm, determine the safe load P (kN) based on weld capacity assuming all welds have equal stress. AP L1 L2
Use LRFD and design the tension members of the roof truss shown in Figure below. Use double-angle shapes throughout and assume 10-mm-thick gusset plates and welded connections. Assume a shear lag factor of U = 0.80. The trusses are spaced at 9 meters. Use A36 steel and design for te following loads. Metal deck : 190 Pa of roof surface Built-up roof : 575 Pa of roof surface Purlins : 145 Pa of roof surface (estimated) Roof Live Load : 960 Pa of horizontal projection Truss weight : 240 Pa of horizontal projection (estimated)
Design the tension members of roof truss shown in the figure. Use double-angle shapes throughout and assume 3/8-inch-thick gusset plates and welded connections. Assume a shear lag factor U = 0.85. The trusses are spaced at 25 feet. Use A572 Grade 50 steel and design for the following loads. Metal deck: 4 psf of roof surface Build-up roof: 12 psf of roof surface Purlins: 6 psf of roof surface (estimated) Snow: 18 psf of horizontal projection Truss weight: 5 psf of horizontal projection (estimated) a. Use LRFD. b. Use ASD.