a tractor attachment thát has an áš an initial cost of 8000$ and a salvage value of 500$ after 8 years. Annual operating costs for the machine are estimated to be 900$ and an interest rate of 20% per year is applicable. :the AW is a) 1155$ (b) -2955$ (c) 2955$ (d) -1155$

a tractor attachment thát has an áš an initial cost of 8000$ and a salvage value of 500$ after 8 years. Annual operating costs for the machine are estimated to be 900$ and an interest rate of 20% per year is applicable. :the AW is a) 1155$ (b) -2955$ (c) 2955$ (d) -1155$

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) A very important component of a system has a mean time between failures of 100 hr and a mean time to repair of 10 hr. Determine the inherent availability of the system. (b) If the equipment in Q7 (c i) above is required to meet an inherent availability requirement of 0.985 and a mean time between failures of 100 hr. Calculate the permissible mean time to repair and if the system as a mean of the time intervals between corrective maintenance actions of 900 hrs and the sum of the mean corrective maintenance time intervals including supply downtime and administrative down time of 10 hrs Determine the operational availability of the system
Based on the Arcticle 4 of RA 8495, what are those differences of the three categories of the practice of Mechanical Engineering.
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
5 “winpgynba uy 514901 1 001 AU YOI J0j A SITFIOM o1 QurwINAG
A local tyre distributor expects to sell approximately 9600 steel belted radial tyres next year. Annual carrying cost in Rs. 16 per tyre and ordering cost is Rs. 75. The economic order quantity of the tyres is A. 64 B. 212 C. 300 D. 1200
Plot DSa and DSw as functions of Tw on a single graph. Plot DSsys [DSsys = DSa +DSw] as functions of Tw on a second graph.
pleassssse solve question 9, statics
A 3000 lb car has a 5-speed manual transmission with 2 .31 ti (transmission ratio) , 1 .22 ti , 4.13 ti , 0 .14 ti , 7 .05 ti . The final drive ratio is 6 .3 ai . The air drag coefficient is 0.32 and the front projected area is 21 square feet. The rolling resistance coefficient is 0.02 and the tire radius is 12 inches. The effective mass factor is 1.0. The power train efficiency is 0.95. The engine wide-open-throttle output torque is shown in the figure. a) Determine the transmission input torque when the vehicle is cruising at a constant speed of 65mph on a 5% slope in the 5th gear. b) When the vehicle speed is 65mph on a 5% slope in the 5th gear, the driver makes a five to four downshift and floors the throttle. Determine the vehicle acceleration immediately after the shift. c) Determine the largest slope the vehicle can negotiate at a speed of 60mph in the 4th gear.
3.16 Do you think that the Aberdeen Three knew about RCRA? If not, should theyhave? Does it really matter if they knew about RCRA or not?
For Problem 19.27 , determine the probability (assuming normal distribution) that a car would need engine maintenance between 70,000 and 90,000 kilometers.
A stepper motor serves as the drive unit for the linear joint of an industrial robot. The joint must have an accuracy of 0.25 mm. The motor is attached to a leadscrew through a 2:1 gear reduction (2 turns of the motor for 1 turn of the leadscrew). The pitch of the leadscrew is 5.0 mm. The mechanical errors in the system (due to backlash of the leadscrew and the gear reducer) can be represented by a normal distribution with standard deviation = ±0.05 mm. Specify the number of step angles that the motor must have in order to meet the accuracy requirement.
The following particulars apply to an inclined belt conveyor: Length of conveyor (loading end to discharge end): 100 mSpeed of belt: 1,5 m/sAngle of wrap around driving pulley: 220 degreesCoefficient of friction between belt and driving pulley: 0,3 Mass of rock conveyed (mass flow rate): 300 t/hThe discharge end is 22 m higher than the loading end. The total friction is equivalent to a force of 6,5 kN in the belt at the head pulley. The efficiency of the drive is 90%. 4.2.1 Calculate the power of the motor. 4.2.2 Calculate the minimum tension in the slack side of the belt as it leaves the driving pulley