A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a bulk supply point. The receiving end apparent power is (1.0 + j0.6) pu and sending end voltage, 1/0°pu. Estimate the following: a) receiving end voltage after two iterations b) perform two further iterations to test the convergence of the value of receiving end voltage deduced in a) b) load current c) sending end apparent power

A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a bulk supply point. The receiving end apparent power is (1.0 + j0.6) pu and sending end voltage, 1/0°pu. Estimate the following: a) receiving end voltage after two iterations b) perform two further iterations to test the convergence of the value of receiving end voltage deduced in a) b) load current c) sending end apparent power

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

1/In the Transmission Line Simulator, the Transmission Line is connected in Nominal-Pi Circuit. Select one: True False
Viva Questions:1. What is the difference between Primary and Secondary constants? 2.Define Transmission line Input Impedance?
Given a telephone transmission line of 100 mile long has Z,=685-j92Q, 0a=0.00497 neper/mile and f=0.0352 rad/mile work at 1000Hz. If Z=2000Q and Eg=10Vrms with Z:=700Q, find the sending end impedance, voltage, current, and power.
1) A TV antenna lead-in wire 10cm long has a characteristic impedance of 250 Ω and is open-circuited at its end. If the line operates at 400 MHz, determine it's input impedance. 2) A telephone line has R = 30 Ω/km, L-100 mHkm, G-0, and C-20 μEkm. At f- 1 kHz, obtain: (a) The characteristic impedance of the line (b) The propagation constant (c) The phase velocity
Find the short circuit current at the D point with the bus-admittance method of the system, whose reactance equivalent is given below.(SB=175MVA UB=154KV)
A cellular radio transmitter has a power output of 3W operating at a frequency of 800MHz, using a 7dB gain antenna. The receiver is located at a distance of 8km with a 12dB antenna from this point. A)Calculate the power received at the receiver and express it in dBm.B)Now consider losses in the transmission lines in both the transmitter and receiver of 1dB and 1.5dB respectively, and calculate the power received at the receiver.
When operating at a frequency of 2 kHz, a cable has an attenuation of 0.25 Np/km and a phase shift of 0.20 rad/km. If a 5V rms signal is applied at the sending end, determine the voltage at a point 10 km down the line, assuming that the termination is equal to the characteristic impedance of the line.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A load impedance of 40 + j70 Ω terminates a 100 Ω transmission line that is 0.3λ long. Find the reflection coefficient and angle at the load, the VSWR on the line, the input impedance and the position of first Vmin and first Vmax from the load.
A transmission line has a characteristic impedance of 100 ohm and a resistance of 0.2 ohm/m. If the line is distortion less, then what will be the attenuation constant associated with the line?
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.