A tube length of 40 cm and a radius of 5 cm passes through the liquid. the viscosity coefficient is 0.8 pois, if the pressure causing the flow is 5 kpa and the pressure in the other side of the tube is 1 kpa calculate 1-the flow velocity at the center of the tube (r=o) 2-the flow velocity at the tube well. (r= R) 3- the velocity of the flow at a point (3 cm) away from the center (r = 3 cm).

A tube length of 40 cm and a radius of 5 cm passes through the liquid. the viscosity coefficient is 0.8 pois, if the pressure causing the flow is 5 kpa and the pressure in the other side of the tube is 1 kpa calculate 1-the flow velocity at the center of the tube (r=o) 2-the flow velocity at the tube well. (r= R) 3- the velocity of the flow at a point (3 cm) away from the center (r = 3 cm).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the flow of a fluid with viscosity ? through a circular pipe. The velocity profile in the pipe is given as u(r) = umax(1 − rn/Rn), where umax is the maximum flow velocity, which occurs at the centerline; r is the radial distance from the centerline; and u(r) is the flow velocity at any position r
Consider the flow of a fluid with viscosity m through a circular pipe. The velocity profile in the pipe is given as u(r) = umax(1 - rn/Rn), where umax is the maximum flow velocity, which occurs at the centerline; r is the radial distance from the centerline; and u(r) is the flow velocity at any position r. Develop a relation for the drag force exerted on the pipe wall by the fluid in the flow direction per unit length of the pipe.
The velocity distribution for the flow of oil with dynamic viscosity of 0.05 Pa-s is given by u(y)=200y(0.1−y)u(y)=200y(0.1−y) where y is in meters. What is the shear stress at the bottom boundary in Pa? see picture
Pure water flows steadily down a surface below the horizontal in a film of thickness h=0.3. mm . Determine the magnitude of the shear stress (N / (m ^ 2)) that acts on the water surface and bottom Assume the kinematic viscosity, v = 1 * 10 ^ - 3 * m ^ 2 / s The velocity profile is given by , u = (hy - (y ^ 2)/2) * g/v
1.3 A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A. 1.4 The absolute viscosity of a fluid at atmospheric conditions is 8 x 10-3 kgf-s/m2. Find this viscosity in: a) Reyn; b) Poise; c) lbf-s/ft2; d) Pa-s.
the nord stream 2 is a pipeline network from used to pump and transport Russian oil to germany. 29286 gallons of oil can be transported per minute through the pipes with an average inside diameter of 50 inches. Given the oil ttranported has a density of 57.99 lbm/ft3 and a viscosity of an 0.0069625 lbm/fts. what is the reynolds number of flow?
A capillary tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum flow rate that can be measured accurately is 0.015 kg/min. If the tube length is 10cm and a maximum pressure of 25 Pa can be measured, determine the tube diameter to be used. The density of the product is 1000 kg/m3.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
An open tank 5m long, 2m deep and 3 m wide contains oil of relative density 0.9 to a depth of 0.9 m. If the tank is accelerated along its length on a horizontal track at a constant value of 3 m/s2 , determine: (i) The new positon of the oil surface. (ii) The pressures at the bottom of the tank at the front and rear edges. (iii) The amount of spill if the tank is given a horizontal acceleration of 4.5 m/s2 instead of 3 m/s2 .
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
Consider the flow of a fluid with viscosity μ through a circular pipe. The velocity profile is shown in the figure, where umax is the maximum velocity, which occurs at the centerline; r is the radial distance from the centerline; u(r) is the flow velocity at any position r. Develop a relation for the drag force exerted on the pipe wall by the fluid in the flow direction per unit length of the pipe
Honey at 1L/min is flowing in a capillary viscometer 2cm in diameterand 50cm long. If the pressure drops is 40kPa, determine its viscosity