A turbine receives steam at the following state: pressure 1200 kPag, enthalpy 2875 kJ/kg, speed 33.3 m/s and elevation 30 m. The steam leaves the turbine at the following state; pressure 20 kPag, enthalpy 2152 kJ/kg, speed 100 m/s and elevation 0 m. Heat is lost to the surroundings at the rate of 29 kJ/s. if the rate of steam flow through the turbine is 0.24 kg/s, what is the power output of the turbine in kW? Assume steady flow conditions. O 598.01 O 143.52 O 112.52 O 165.56

A turbine receives steam at the following state: pressure 1200 kPag, enthalpy 2875 kJ/kg, speed 33.3 m/s and elevation 30 m. The steam leaves the turbine at the following state; pressure 20 kPag, enthalpy 2152 kJ/kg, speed 100 m/s and elevation 0 m. Heat is lost to the surroundings at the rate of 29 kJ/s. if the rate of steam flow through the turbine is 0.24 kg/s, what is the power output of the turbine in kW? Assume steady flow conditions. O 598.01 O 143.52 O 112.52 O 165.56

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine operates under steady flow conditions, receiving steam at the following state: pressure 1200 KPa, temperature 1880°C, enthalpy 2785 KJ/kg, speed 33.3 m/s and elevation 3 m. The steam leaves the turbine at the following pressure 20 KPa, enthalpy 2512 KJ/kg, speed 100 m/s and elevation 0 m. Heat is lost to the surroundings at the rate of 0.29 KJ/s. If the rate of steam flow through the turbine is 0.42 kg/s. Find: A. Potential Energy 1, KJ/kg. B. Potential Energy 2 in KJ/kg. C. Kinetic Energy 1 in KJ/kg. D. Kinetic Energy 2 in KJ/kg. E. Heat Energy in KJ/kg. F. Power Output in KW.
A turbine operates under steady flow conditions, receiving steam at the following state: pressure 1200 kPa, temperature 1880C, enthalpy 2785 kJ/kg, speed 33.3 m/s, and elevation 3 m. The steam leaves the turbine at the following pressure 20 kPa, enthalpy 2512 kJ/kg, speed 100 m/s, and elevation 0 m. Heat is lost to the surroundings at the rate of 0.29 kJ/s. If the rate of steam flow through the turbine is 0.42 kg/s, what is the power output of the turbine in kW?
Steam enters a turbine stage with an internal energy of 3,072 kJ/kg at 69 m/s and leaves the same stage with an internal energy of 2,111 kJ/kg and a velocity of 113. Calculate the power (in kW) if there are 1.965 kg/s steam admitted at the turbine throttle?
Air at 7°C enters a turbojet engine at a rate of 16 kg/s and at a velocity of 220 m/s (relative to the engine). Air is heated in the combustion chamber at a rate 15,000 kJ/s, and it leaves the engine at 427°C. Determine the thrust produced by this turbojet engine. (Hint: Choose the entire engine as your control volume.)
In a gas turbine , the flow rate of air is 4 kg/sec . The velocity and enthalpy of air at the entrance are 200 m/sec and 6000 KJ/kg respectively . At the exit , the velocity is 100 m/sec and enthlpy is 5000 KJ /kg . A loss of heat of 40 KJ/kg occurs while the air passes through the turbine . Determine the power developed by the turbine
Steam enters a turbine with a pressure of P1 = (5000 – K) kPa, specific internal energy u1 = (3500 + K) kJ/kg, mass flow rate of 7.5 kg/s and density of ρ1 = [1 + (K/1000)] kg/m3. Steam leaves at P2 = (2K) kPa with a density of ρ2 = 4.5 kg/m3and a specific internal energy of u2 = (1000 + 2K) kJ/kg. Heat loss from the device by radiation is 50 kJ/kg. Neglecting the changes in kinetic and potential energies, determine the power produced by the system. k=893
A steam turbine is designed to operate at a mass flow of 1.5 kg / h. Entry state to the turbine P1=2 MPa, T1=400'C and V1=60m/s; the output state is P2=0.1MPa, x2 = 0.97 and V2=150m / s. The height difference between the turbine inlet and outlet is 1 m. The heat loss from the turbine is given as 50 kW. a) Determine the power generated from the turbine. b) Calculate the turbine power by neglecting the kinetic and potential energy changes. Comment these two results. c) Calculate the turbine inlet and outlet cross-sectional areas, as well as the steam pipe diameters. d) If the ambient temperature is 27'C, what is the entropy generation in the turbine?
One kilogram per second of steam enters a turbine stage with an internal energy of360 kJ/kg, pressure of 100 kPa, specific volume 0.013 m3/kg at 70 m/s and leaves theturbine with the internal energy of 230 kJ/kg, pressure of 70 kPa, specific volume of 0.12m3/kg and a velocity of 124 m/sec and there is no change of elevation. Heat loss of theturbine is 100 kJ/s. Calculate the work done by the system in kW.
Water vapor enters the steam turbine at 4000 kPa pressure, 500 ° C temperature and 6 m 3 / s volume flow , as shown in the figure below . 0.2 times the mass flow rate of the incoming water from outlet no.2 with 500 kPa pressure and 200 ° C temperature, 0.8 times the mass flow of water, exit no 3 with 30 kPa pressure and 0.85 dryness degree. Since the heat transfer from the turbine to the environment is 5000 kW,(Changes in kinetic and potential energies are negligible) find the mass flow of the incoming water . Find the volume flow of water at outlet no. 3 Find the power (kW) produced by the turbine.
A pump-turbine is a piece of equipment that can operate either as a pump or as a turbine, depending on the direction of the water flow. The picture on the right shows a pump-turbine system.When it is daytime, this system is used as a turbine, taking water from the upper reservoir and discharging it into the lower reservoir, producing electricity. When it is nighttime, electricity is cheaper, and this system is used as a pump, taking water from the lower reservoir and discharging it into the higher reservoir, so that it can produce electricity again the next day when it is used as a turbine. Consider that, using the system as a turbine or pump, the water flow is 1m3/s and the pressure drop is 5 m, determine:(a) The power extracted from the fluid by the turbine (points 1 and 2 are as shown in the figure: z1=35 m and z2=0 m).(b) The useful power delivered to the fluid by the pump (points 1 and 2 in the figure should be reversed: z1=0 m and z2=35 m).
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Steam flows into a turbine at the rate of 10 kg/s and 10 kW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine.Note : h1 = 2739 kJ /kg and h2 = 2300.5 kJ / kg CHOICES: A. 4605 kW B. 4973 kW C. 4375 kW D. 4000 kW