A turning operation is performed with HSS tooling on mild steel, with Taylor tool life parameters n = 0.12, C = 60 m/min. Work part length = 450 mm and diameter = 80 mm. Feed = 0.20 mm/rev. Handling time per piece = 4.0 min, and tool change time = 1.5 min. Cost of machine and operator = $27/hr, and tooling cost = $2 per cutting edge. Find the a. cutting speed for maximum production rate and b. cutting speed for minimum cost Equations used n *-=c(") * Vmax = C 1-n Tt 1 Vmin = C Co n Pad-C(₁) n CoTt + Ct )"

A turning operation is performed with HSS tooling on mild steel, with Taylor tool life parameters n = 0.12, C = 60 m/min. Work part length = 450 mm and diameter = 80 mm. Feed = 0.20 mm/rev. Handling time per piece = 4.0 min, and tool change time = 1.5 min. Cost of machine and operator = $27/hr, and tooling cost = $2 per cutting edge. Find the a. cutting speed for maximum production rate and b. cutting speed for minimum cost Equations used n -=c(") Vmax = C 1-n Tt 1 Vmin = C Co n Pad-C(₁) n CoTt + Ct )"

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
Please give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VT0.25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is?
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
A job has to be machined in shaping and the process parameters are given below: Length of the job=120 mm Speed of the motor=640 rpm Cutting speed=248 m/min Tool allowance before cutting =31.5 mm Tool allowance after cutting=10 mm Determine the cutting to return stroke ratio for the above operation and draw the arrangement of machining with tool head and allowances.
In orthogonal turning of a bar 100 mm diameter with a feed of 0.25 mm/rev., depth of cut = 4 mm, cutting velocity = 90 m/min. it is observed that the main cutting force is perpendicular to friction force acting at the chip tool interface and cutting force is 1500 N. find (i) rake angle (ii) normal force.
A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.
A slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide annealed mild steel block at a feed f=0.20mm/tooth and depth of cut d=2.5mm. The cutter is D=45 mm in dimater, has 20 straight teeth, rotates at N=110rpm and by the definition, is wider than the block to be machined. Calculate;1. Material removal2. Estimate the power and torque required for this operation3. Calculate the cutting time
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
Low carbon steel having a tensile strength of 450 MPa and a shear strength of 270 MPa is cut in a turning operation with a cutting speed of 2500 mm/s. The feed is 0.15 mm/rev, and the depth of cut is 0.25 cm. The rake angle of the tool is 12° in the direction of chip flow. The resulting chip ratio is 0.55. Using the orthogonal model as an approximation of turning, determine (a) the shear plane angle, (b) shear force, (c) cutting force and feed force.
In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle  = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work done
Manufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mm
For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a matrix of 0.1 mm (0.004 in) diameter holes in a plate of 3.2 mm (0.125 in) thick hardened tool steel. The matrix is rectangular, 75 by 125 mm (3.0 by 5.0 in) with the separation between holes in each direction = 1.6 mm ( 0.0625 in).